RST-D 87-12
ID 315513
- トルク: 7.9 Nm
Technical details
| 回転角度 [°] | 30.0 |
|---|---|
| ピッチ | 12.0 |
| 回転方向 | 両側で |
| トルク [Nm] | 7.9 |
| 重量 [kg] | 2.9 |
| IP 保護等級 | 50 |
| ロック時間 [s] | 0.1 |
| アンロック時間 [s] | 0.1 |
| 最低周囲温度 [°C] | 5.0 |
| 最高周囲温度 [°C] | 60.0 |
| 最低作動圧力 [bar] | 4.0 |
| 最大作動圧 [bar] | 8.0 |
| 呼び作動圧力 [bar] | 6.0 |
| ダブルストロークあたりのシリンダー容積 [cm³] | 19.0 |
| 繰り返し精度 [°] | 0.06 |
| 振れサイクルリング [mm] | 0.02 |
| 軸方向の振れサイクルリング [mm] | 0.02 |
| パラレルサイクルリング [mm] | 0.04 |
| 油圧ショックアブソーバーの数 | 2.0 |
| 長さ X [mm] | 136.0 |
| 幅 Y [mm] | 100.0 |
| 高さ Z [mm] | 74.0 |
| トルク My 最大 [Nm] | 40.0 |
| モーメント Mz最大 [Nm] | 40.0 |
| 最大軸方向力 Fz (最大) [N] | 3400.0 |
| 最大径方向力 Fr (最大) [N] | 1700.0 |
寸法と最大荷重
旋回時間
寸法と最大荷重
表示されたモーメントと力は静的な値であり、同時に発生することがあります確実に衝撃や縦揺れなく旋回するよう、絞りを行う必要があります。スロットリングを行わない場合耐用年数が短くなります。
旋回時間
- X-axis:
- 旋回時間
- Y-axis:
- 質量慣性モーメント
- X-axis top:
- サイクル数 / 時
General notes about the series
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Drive ring
The position of the drive ring is always drawn in basic position. From here, the ring turns clockwise or anti-clockwise.
Swiveling time
is the rotation time of pinion/flange around the nominal rotation angle. Valve switching times, hose filling times, or PLC reaction times are not included and are to be considered when cycle times are calculated.
Reference sensor
For monitoring the basic position, an inductive sensor can be attached, which will be actuated every 360°. It can be used for reference run or for checking if the control unit has counted correctly.
Swivel time depends on the payload
The shown diagrams are valid for nominal rotation angles, for the use with vertical swivel axis, or for centrical payloads with horizontal swivel axes, and at an operating pressure of 6 bar. The diagrams show the expected swivel time, and allows cycle per hour depending on the mass moments of inertia. The swiveling times need to be adjusted by using throttle valves, otherwise the life time could be reduced. We will be happy to help you designing other applications.
Total cycle time
The total cycle time consists of the swiveling time per cycle together with other required time intervals. See the operating manual for the exact calculation of the total cycle time.
Housing material
Aluminum alloy, anodized
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Operating principle
Rack and pinion principle with back stroke freewheel
Scope of delivery
Centering elements, safety information (product-specific instructions available online)
Warranty
24 months
Service life characteristics
on request