PGN 300-1-AS
IDnr. 370406
Alternatieve producten:
- 片側ストローク: 35 mm
- 閉力: 6000 N
- 最高周囲温度: 90 °C
Technische gegevens
| 죠당 스트로크 [mm] | 35.0 |
|---|---|
| 폐쇄력 [N] | 6000.0 |
| 최소 탄성력 [N] | 1500.0 |
| 중량 [kg] | 15.5 |
| 권고 공작물 중량 [kg] | 22.5 |
| 더블 스트로크당 실린더 용량 [cm³] | 885.0 |
| 최소 작동 압력 [bar] | 4.0 |
| 최대 작동 압력 [bar] | 6.5 |
| 정격 가동 압력 [bar] | 6.0 |
| 최소 에어 퍼지 압력 [bar] | 0.5 |
| 최대 에어 퍼지 압력 [bar] | 1.0 |
| 폐쇄 시간 [s] | 0.6 |
| 개방 시간 [s] | 1.2 |
| 스프링 포함 폐쇄/개방 시간 [s] | 1.3 |
| 최대 허용 가능 핑거 길이 [mm] | 250.0 |
| 핑거당 최대 허용 무게 [kg] | 9.0 |
| IP 보호등급 | 40 |
| 최소 주위 온도 [°C] | 5.0 |
| 최대 주위 온도 [°C] | 90.0 |
| 반복 정밀도 [mm] | 0.02 |
| 모멘트 Mx 최대 [Nm] | 240.0 |
| 모멘트 My 최대 [Nm] | 240.0 |
| 모멘트 Mz 최대 [Nm] | 168.0 |
| 최대 축 포스 Fz 최대 [N] | 4800.0 |
최대 로드
파지력, O.D. 그리핑
최대 허용 핑거 추정
최대 로드
움직임과 힘은 각각의 베이스 죠에 적용되며 동시에 스스로도 발생할 수 있습니다. My는 파지력 자체에 의해서 생성되는 모멘트에 추가로 발생할 수 있습니다.
파지력, O.D. 그리핑
- X-as:
- 포인트 P - 핑거 길이
- Y-as:
- 파지력
최대 허용 핑거 추정
Lmax는 최대치의 허용 핑거 길이에 해당합니다. 기술 데이터 표를 참조하십시오.
- green
- 허용 범위
- grey
- 허용 불가 범위
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Wedge-hook kinematics
Housing material
Aluminum alloy, anodized
Base jaw material
Steel
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
24 months
Scope of delivery
Brackets for proximity switches (only for sizes 64, 80), centering pins, O-rings for direct connection, assembly and operating manual with manufacturer’s declaration
Gripping force maintenance
possible by using the version with mechanical gripping force maintenance or pressure maintenance valve SDV-P