DPZ-plus 50-1
ID 1316268
- Hub pro Backe: 4 mm
- Schließkraft: 290 N
- Öffnungskraft: 320 N
- Max. Umgebungstemperatur: 90 °C
Technical details
| Course par mors [mm] | 4.0 |
|---|---|
| Force à la fermeture [N] | 290.0 |
| Force à l'ouverture [N] | 320.0 |
| Force de fermeture (avec longueurs de doigt de 0 mm) [N] | 347.0 |
| Force d'ouverture (avec longueurs de doigt de 0 mm) [N] | 380.0 |
| Poids [kg] | 0.37 |
| Poids de pièce recommandé [kg] | 1.45 |
| Volume du cylindre par course double [cm³] | 9.0 |
| Pression d'utilisation min. [bar] | 2.5 |
| Pression d'utilisation maximale [bar] | 8.0 |
| Pression d'utilisation nominale [bar] | 6.0 |
| Pression de purge d'air min. [bar] | 0.2 |
| Pression de purge d'air max. [bar] | 0.5 |
| Temps de fermeture [s] | 0.03 |
| Tiempo de apertura [s] | 0.03 |
| Longitud máxima admisible de los dedos [mm] | 50.0 |
| Peso máx. admisible por dedo [kg] | 0.15 |
| Clase de protección IP | 67 |
| Temperatura ambiente mín. [°C] | 5.0 |
| Temperatura ambiente máx. [°C] | 90.0 |
| Precisión de repetición [mm] | 0.01 |
| Normativa para sala blanca ISO 14644-1 | 5 |
| Categoría de sala blanca: ISO 14644-1 | 1999 |
| Diámetro D [mm] | 80.6 |
| Altura Z [mm] | 40.5 |
| Momento Mx máx. [Nm] | 15.0 |
| Momento My máx. [Nm] | 19.0 |
| Momento Mz máx. [Nm] | 8.0 |
| Máx. fuerza axial Fz máx. [N] | 375.0 |
Pueden ser necesarios 100 ciclos de agarre hasta que esté disponible la fuerza de agarre total (según lo indicado en la tabla de datos).
Afmetingen en maximaal toegelaten belasting
Fuerza de agarre en el cierre
Grijpkracht, grijpen van binnendiameter
Afmetingen en maximaal toegelaten belasting
De opgegeven waarden voor moment en kracht zijn statische waarden, gelden voor elke basisklem en kunnen tegelijkertijd voorkomen. Naast het moment dat door de grijpkracht zelf wordt gegeneerd, kunnen er nog extra lasten optreden.
Fuerza de agarre en el cierre
- X-axis:
- Punt P - Vingerlengte
- Y-axis:
- Grijpkracht
Grijpkracht, grijpen van binnendiameter
- X-axis:
- Punt P - Vingerlengte
- Y-axis:
- Grijpkracht
General notes about the series
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Note – tightness
Please note that to achieve an IP 67 protection class, the gripper requires an additional hose for ventilation or a switchable air purge connection. For detailed information, please refer to the assembly and operating manual. Alternatively, a sinter filter (supplied) mounted on the air purge connection can prevent the penetration of dirt particles > 0.12 mm. However, this reduces the protection class to IP 54.
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Wedge-hook kinematics
Housing material
Aluminum alloy, anodized
Base jaw material
Steel
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
36 months
Service life characteristics
on request
Scope of delivery
Centering sleeves, centering pins, O-rings for direct connection, assembly instructions (operating manual with declaration of incorporation is available online)
Gripping force maintenance
possible by using the version with mechanical gripping force maintenance or pressure maintenance valve SDV-P