PPU-E 30-H270-V100-03-F12
- stroke horizontal [Y-axis]: 270 mm
- stroke vertical [Z-axis]: 100 mm
- Max. payload: 3 kg
Technical details
| 传动概念 | 线性电机驱动 |
|---|---|
| 行程水平[Y 轴] [mm] | 270.0 |
| 行程垂直[Z 轴] [mm] | 100.0 |
| 最大传动力 [Y 轴] [N] | 400.0 |
| 标称力 [Y 轴] [N] | 150.0 |
| 最大传动力 [Z 轴] [N] | 550.0 |
| 标称力 [Z 轴] [N] | 195.0 |
| 最大有效荷载 [kg] | 3.0 |
| 重复精度[Y 轴] [mm] | 0.01 |
| 重复精度[Z 轴] [mm] | 0.01 |
| 最大电流[Y 轴] [A] | 8.0 |
| 静止电流[Y 轴] [A] | 1.8 |
| 最大电流[Z 轴] [A] | 12.0 |
| 静止时电流[Z 轴] [A] | 3.2 |
| 最低环境温度 [°C] | 10.0 |
| 最高环境温度 [°C] | 40.0 |
| 重量 [kg] | 27.6 |
| 行程测量系统接口 | Sin/Cos 1Vss |
| 为 C 轴制备 | ERD 12 |
| 流体通路数量 | 2.0 |
| 输出端弯管接头数量 | 1.0 |
| 间隙 N（力矩负载） [mm] | 73.0 |
| 长度 X [mm] | 113.0 |
| 宽度 Y [mm] | 335.0 |
| 高度 Z [mm] | 745.2 |
| 力矩 Mx max. [Nm] | 24.0 |
| 力矩 My max. [Nm] | 6.0 |
| 力矩 Mz max. [Nm] | 50.0 |
| 力 Fx max. [N] | 50.0 |
| 力 Fy max. [N] | 400.0 |
| 力 Fz max. [N] | 550.0 |
| 带 C 轴的型号 | 是 |
尺寸和最大载荷
周期
尺寸和最大载荷
所示力矩和力为静态值，可能会同时出现。
周期
- X-axis:
- 安装尺寸
- Y-axis:
- 周期
General notes about the series
Safety notes
Caution: Magnetic field! This particularly applies for persons with implanted medical devices, such as pacemakers, hearing aids, etc.
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Payload
is the weight of the total weight which is attached to the cantilever arm. Please consider that service life will shorten if the maximum payload is exceeded. SCHUNK cannot assume any warranty for this.