D 200-SSS-MM-3210-SL
- Course max.: 1470 mm
- Force max. d'entraînement: 10000 N
Détails techniques
| Course max. H [mm] | 1470.0 |
|---|---|
| Force max. d'entraînement [N] | 10000.0 |
| Répétabilité [mm] | ± 0.03 |
| Longueur totale max. [mm] | 2000.0 |
| Vitesse de rotation max. [m/s] | 0.5 |
| Accélération max. [m/s²] | 20.0 |
| Température ambiante mini. [°C] | 0.0 |
| Température ambiant maxi. [°C] | 80.0 |
| Poids propre de la base, chariot inclus [kg] | 28.5 |
| Supplément de masse par course de 100 mm [kg] | 2.6 |
| Poids du chariot [kg] | 11.0 |
| Longueur de la plaque du chariot [mm] | 400.0 |
| Glissière | Guidage par rail |
| Nombre de rails | 2.0 |
| Taille des rails | 25 |
| Concept d'entraînement | Entraînement par vis |
| Couple à vide [Nm] | 2.8 |
| Moment d'inertie [kgm²] | 6.39E-4 |
| Diamètre de broche [mm] | 32.0 |
| Pas de vis [mm] | 10 |
| vitesse de broche max. [1/min] | 3000.0 |
| Longueur X [mm] | 530.0 |
| Largeur Y [mm] | 200.0 |
| Hauteur Z [mm] | 125.0 |
| Moment Mx max. [Nm] | 3500.0 |
| Moment My max. [Nm] | 6000.0 |
| Moment Mz max. [Nm] | 4500.0 |
| Force Fy max. [N] | 5000.0 |
| Force Fz max. [N] | 8000.0 |
| Force -Fz max. [N] | 5000.0 |
尺寸和最大载荷
Supports de broche**
尺寸和最大载荷
此处所示力和力矩均为各荷载的最大值。如果同时施加多个力和/或力矩，允许的最大个别值将更低。
Supports de broche**
- Axe X:
- Longueur d'axe
- Axe Y:
- Vitesse de rotation
General notes about the series
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Max. stroke
is the maximum permissible stroke. Acceleration and braking distances or possible overrun must be taken into consideration.
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Acceleration and speed
The values specified are the maximum values of the units without loading. The actual accelerations and speeds for your application must be designed separately and can deviate from the maximum values.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Operating principle
Choice of toothed belt or ball screw spindle drive
Drive
servomotors of different providers can be trouble-free adapted
Profile
Extruded aluminum profile with plastic cover strip
Slide
Aluminum slide with a brush seal
Scope of delivery
Assembly and operating manual with declaration of incorporation
Warranty
24 months