SWG 40
ID 305108
- Angle d'ouverture: 15 °
- Couple à la fermeture: 1.2 Nm
- Température ambiant maxi.: 90 °C
기술 세부 정보
| Force de fermeture (avec longueurs de doigt de 0 mm) [N] | 153.0 |
|---|---|
| Angle d'ouverture par doigt [°] | 15.0 |
| Angle position fermée par doigt jusqu'à [°] | 7.0 |
| Couple à la fermeture [Nm] | 1.2 |
| Moment de fermeture généré par ressort [Nm] | 0.36 |
| Poids [kg] | 0.106 |
| Poids de pièce recommandé [kg] | 0.24 |
| Volume du cylindre par course double [cm³] | 1.6 |
| Pression d'utilisation min. [bar] | 4.0 |
| Pression d'utilisation maximale [bar] | 6.5 |
| Pression d'utilisation nominale [bar] | 6.0 |
| Temps de fermeture [s] | 0.025 |
| Temps d'ouverture [s] | 0.03 |
| Longueur de doigt max. admissible [mm] | 35.0 |
| Poids de doigt max. admissible [kg] | 0.05 |
| Indice de protection IP | 30 |
| Température ambiante mini. [°C] | 5.0 |
| Température ambiant maxi. [°C] | 90.0 |
| Répétabilité [mm] | 0.05 |
| Longueur X [mm] | 40.0 |
| Largeur Y [mm] | 20.0 |
| Hauteur Z [mm] | 52.0 |
| Moment Mx max. [Nm] | 0.35 |
| Moment Mz max. [Nm] | 0.35 |
| Force axiale max. Fz max. [N] | 30.0 |
Dimensions and maximum loads
Maximum permitted finger projection
Gripping force O.D. gripping
Closing moment curve
Maximum permitted finger projection
Dimensions and maximum loads
The indicated torques and forces are static values, apply for each base jaw, and may occur simultaneously.
Maximum permitted finger projection
Gripping force O.D. gripping
- X축:
- Point P - Finger length
- Y축:
- Gripping force
Closing moment curve
- X축:
- Opening angle
- Y축:
- Closing moment
Maximum permitted finger projection
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
General notes about the series
Closing moment
is the arithmetic sum of the individual moment applied to each jaw.
Finger length
is measured from the reference surface as the distance P in direction to the main axis.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
double-acting, guided kinematics
Housing material
Aluminum alloy, anodized
Base jaw material
Aluminum alloy, anodized
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
24 months
Service life characteristics
on request
Scope of delivery
Gripper in the ordered variant, accessory kit (centering sleeves/detailed contents see operating manual) and safety information. Product-specific instructions can be downloaded at schunk.com/downloads-manuals.
Gripping force maintenance
always integrated by using springs, and also possible via pressure maintenance valve SDV-P