PLG 50-XXX-2-OSY
- Carrera por mordaza: 400 mm
- Fuerza de cierre: 4750 N
- Fuerza de apertura: 5100 N
- Temperatura ambiente máx.: 90 °C
Información técnica
| Version de doigt | long |
|---|---|
| Synchronisation | sans synchronisation |
| Course min. par doigt [mm] | 100.0 |
| Course max. par doigt [mm] | 400.0 |
| Force à la fermeture [N] | 4750.0 |
| Force à l'ouverture [N] | 5100.0 |
| Poids* [kg] | 58.04 |
| Poids supplémentaire par course de 1 mm** [kg] | 0.079 |
| Poids de pièce recommandé [kg] | 23.75 |
| Pression d'utilisation min. [bar] | 2.0 |
| Pression d'utilisation maximale [bar] | 6.0 |
| Pression d'utilisation nominale [bar] | 6.0 |
| Temps de fermeture [s] | 1.0 |
| Temps d'ouverture [s] | 1.3 |
| Longueur de doigt max. admissible [mm] | 800.0 |
| Poids de doigt max. admissible [kg] | 25.0 |
| Indice de protection IP | 30 |
| Température ambiante mini. [°C] | 5.0 |
| Température ambiant maxi. [°C] | 90.0 |
| Répétabilité [mm] | 0.03 |
| Moment Mx max. [Nm] | 357.0 |
| Moment My max. [Nm] | 1300.0 |
| Moment Mz max. [Nm] | 500.0 |
| Force de maintien serrage de position *** [N] | 4200.0 |
| Force axiale max. Fz max. [N] | 5000.0 |
* se réfère à la variante de base montrée avec une course de 100 mm par mors sans option supplémentaires
** se réfère à la version de base sans options supplémentaires
se réfère à la version avec bloacage en position
Max. loads
Maximum permitted finger projection
Force de préhension, préhension extérieure
Force de préhension, préhension intérieure
Charge des moments
Finger version: short finger length
Finger version: long finger length
Max. loads
The indicated moments and forces are statical values, apply for each base jaw and may appear simultaneously. Loads may occur in addition to the moment generated by the gripping force itself. Please also refer to the diagram for the moment loads.
Maximum permitted finger projection
Force de préhension, préhension extérieure
- Eje X:
- Longueur des doigts
- Eje Y:
- Force de préhension
Force de préhension, préhension intérieure
- Eje X:
- Longueur des doigts
- Eje Y:
- Force de préhension
Charge des moments
Finger version: short finger length
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
Finger version: long finger length
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
How to get to the online configurator
The configurator can be accessed via the SCHUNK website or via https://schunk.com/us/en/konfigurator-plg available directly.
Holding force position clamping
describes the sum of the clamping force on the piston rods of the two installed clamping elements.
Housing material
Aluminum alloy
Base jaw material
hard-anodized, high strength aluminum
Warranty
12 months
Scope of delivery
Centering sleeves for finger mounting, mounting material for gripper mounting for variants with AKO EN ISO..., assembly instructions (operating manual with declaration of incorporation available online).