PLG 50-XXX-2-OSY
- Stroke per jaw: 400 mm
- Closing force: 4750 N
- Opening force: 5100 N
- Max. ambient temperature: 90 °C
Información técnica
| Finger version | long |
|---|---|
| Synchronization | without synchronization |
| Min. stroke per jaw [mm] | 100.0 |
| Max. stroke per jaw [mm] | 400.0 |
| Closing force [N] | 4750.0 |
| Opening force [N] | 5100.0 |
| Weight* [kg] | 58.04 |
| Additional mass per 1 mm stroke** [kg] | 0.079 |
| Recommended workpiece weight [kg] | 23.75 |
| Min. operating pressure [bar] | 2.0 |
| Max. operating pressure [bar] | 6.0 |
| Nominal operating pressure [bar] | 6.0 |
| Closing time [s] | 1.0 |
| Opening time [s] | 1.3 |
| Max. permissible finger length [mm] | 800.0 |
| Max. permissible weight per finger [kg] | 25.0 |
| IP protection class | 30 |
| Min. ambient temperature [°C] | 5.0 |
| Max. ambient temperature [°C] | 90.0 |
| Repeat accuracy [mm] | 0.03 |
| Moment Mx max. [Nm] | 357.0 |
| Moment My max. [Nm] | 1300.0 |
| Moment Mz max. [Nm] | 500.0 |
| Holding force position clamping *** [N] | 4200.0 |
| Max. axial force Fz max. [N] | 5000.0 |
* referring to the basic variant shown with 100 mm stroke per jaw without additional options
** referring to the basic variant without additional options
referring to the variant with position clamping
Charges max.
Dépassement maximum autorisé
Force de préhension, préhension extérieure
Force de préhension, préhension intérieure
Charge des moments
Version du doigt : longueur de doigt courte
Version du doigt : longueur de doigt longue
Charges max.
Les moments et les forces indiqués correspondent à des valeurs statiques et s'appliquent à chacun des mors de base et peuvent survenir simultanément. Des charges peuvent s'ajouter au moment produit par la force de préhension. Veuillez également vous référer au diagramme pour les moments admissibles.
Dépassement maximum autorisé
Force de préhension, préhension extérieure
- Eje X:
- Longueur des doigts
- Eje Y:
- Force de préhension
Force de préhension, préhension intérieure
- Eje X:
- Longueur des doigts
- Eje Y:
- Force de préhension
Charge des moments
Version du doigt : longueur de doigt courte
Lmax correspond à la longueur de doigt maximale admissible, voir tableau des caractéristiques techniques.
- green
- Plage admissible
- grey
- Plage non admissible
Version du doigt : longueur de doigt longue
Lmax correspond à la longueur de doigt maximale admissible, voir tableau des caractéristiques techniques.
- green
- Plage admissible
- grey
- Plage non admissible
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
How to get to the online configurator
The configurator can be accessed via the SCHUNK website or via https://schunk.com/us/en/konfigurator-plg available directly.
Holding force position clamping
describes the sum of the clamping force on the piston rods of the two installed clamping elements.
Housing material
Aluminum alloy
Base jaw material
hard-anodized, high strength aluminum
Warranty
12 months
Scope of delivery
Centering sleeves for finger mounting, mounting material for gripper mounting for variants with AKO EN ISO..., assembly instructions (operating manual with declaration of incorporation available online).