PZN-plus 300-2-IS
ID 303647
- Course par mors : 20 mm
- Force à l'ouverture: 37300 N
- Température ambiant maxi.: 90 °C
기술 세부 정보
| 죠당 스트로크 [mm] | 20.0 |
|---|---|
| 개방력 [N] | 37300.0 |
| 개방력(핑거 길이 0mm) [N] | 39574.0 |
| 최소 탄성력 [N] | 10500.0 |
| 중량 [kg] | 43.5 |
| 권고 공작물 중량 [kg] | 127.5 |
| 더블 스트로크당 실린더 용량 [cm³] | 5050.0 |
| 최소 작동 압력 [bar] | 4.0 |
| 최대 작동 압력 [bar] | 6.5 |
| 정격 가동 압력 [bar] | 6.0 |
| 최소 에어 퍼지 압력 [bar] | 0.5 |
| 최대 에어 퍼지 압력 [bar] | 1.0 |
| 폐쇄 시간 [s] | 2.0 |
| 개방 시간 [s] | 1.2 |
| 스프링 포함 폐쇄/개방 시간 [s] | 2.0 |
| 최대 허용 가능 핑거 길이 [mm] | 200.0 |
| 핑거당 최대 허용 무게 [kg] | 11.5 |
| IP 보호등급 | 40 |
| 최소 주위 온도 [°C] | 5.0 |
| 최대 주위 온도 [°C] | 90.0 |
| 반복 정밀도 [mm] | 0.05 |
| 클린룸 클래스 ISO 14644-1 | 5 |
| 직경 D [mm] | 345.0 |
| 높이 Z [mm] | 196.0 |
| 모멘트 Mx 최대 [Nm] | 400.0 |
| 모멘트 My 최대 [Nm] | 400.0 |
| 모멘트 Mz 최대 [Nm] | 280.0 |
| 최대 축 포스 Fz 최대 [N] | 8000.0 |
Dimensions and maximum loads
Gripping force I.D. gripping
Dimensions and maximum loads
The indicated moments and forces are statical values, apply for each base jaw and may appear simultaneously. Loads may additionally occur to the moment produced by the gripping force itself.
Gripping force I.D. gripping
- X축:
- Point P - Finger length
- Y축:
- Gripping force
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Cleanroom class ISO 14644-1:1999
5
Principe de fonctionnement
Cinématique à rampe forcée
Matériau du corps
Alliage d'aluminium anodisé
Matière des mors de base
Acier
Actionnement
pneumatique, par air comprimé filtré selon la norme ISO 8573-1:2010 [7:4:4].
Garantie
36 mois
Caractéristiques de la durée de vie
sur demande
Etendue de la livraison
Pince dans la variante commandée, lot séparé pochette annexe (douilles de centrage, joints toriques pour un raccordement direct / contenus détaillés dans le manuel d'utilisation) et consignes de sécurité. Les instructions spécifiques aux produits peuvent être téléchargées sur schunk.com/downloads-manuals.
Maintien de la force de préhension
possible avec maintien mécanique de la force de préhension ou clapet anti-retour SDV-P