PLG 20-XXX-1-ASY
- Hub pro Backe: 400 mm
- Schließkraft: 1650 N
- Öffnungskraft: 2000 N
- Max. Umgebungstemperatur: 90 °C
Technische Details
| Fingerversion | kurz |
|---|---|
| Synchronisierung | Asynchron |
| Hub pro Backe min. [mm] | 100.0 |
| Hub pro Backe max. [mm] | 400.0 |
| Schließkraft [N] | 1650.0 |
| Öffnungskraft [N] | 2000.0 |
| Eigenmasse* [kg] | 19.03 |
| Zusatzmasse je 1 mm Hub** [kg] | 0.05 |
| Empfohlenes Werkstückgewicht [kg] | 8.25 |
| Min. Betriebsdruck [bar] | 2.0 |
| Max. Betriebsdruck [bar] | 6.0 |
| Nennbetriebsdruck [bar] | 6.0 |
| Schließzeit [s] | 0.8 |
| Öffnungszeit [s] | 1.0 |
| Max. zulässige Fingerlänge [mm] | 330.0 |
| Max. zulässige Masse pro Finger [kg] | 15.0 |
| Schutzart IP | 30 |
| Min. Umgebungstemperatur [°C] | 5.0 |
| Max. Umgebungstemperatur [°C] | 90.0 |
| Wiederholgenauigkeit [mm] | 0.03 |
| Moment Mx max. [Nm] | 136.0 |
| Moment My max. [Nm] | 413.0 |
| Moment Mz max. [Nm] | 154.0 |
| Haltekraft Positionsklemmung *** [N] | 1600.0 |
| Max. Kraft axial Fz max. [N] | 2000.0 |
* bezogen auf die dargestellte Basisvariante mit 100 mm Hub pro Backe ohne zusätzliche Optionen
** bezogen auf die Basisvariante ohne zusätzliche Optionen
bezogen auf die Variante mit Positionsklemmung
Max. loads
Maximum permitted finger projection
Greifkraft Außengreifen
Gripping force I.D. gripping
Moment loading
Finger version: short finger length
Finger version: long finger length
Max. loads
The indicated moments and forces are statical values, apply for each base jaw and may appear simultaneously. Loads may occur in addition to the moment generated by the gripping force itself. Please also refer to the diagram for the moment loads.
Maximum permitted finger projection
Greifkraft Außengreifen
- X-Achse:
- Fingerlänge
- Y-Achse:
- Greifkraft
Gripping force I.D. gripping
- X-Achse:
- Finger length
- Y-Achse:
- Gripping force
Moment loading
Finger version: short finger length
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
Finger version: long finger length
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
How to get to the online configurator
The configurator can be accessed via the SCHUNK website or via https://schunk.com/us/en/konfigurator-plg available directly.
Holding force position clamping
describes the sum of the clamping force on the piston rods of the two installed clamping elements.
Housing material
Aluminum alloy
Base jaw material
hard-anodized, high strength aluminum
Warranty
12 months
Scope of delivery
Centering sleeves for finger mounting, mounting material for gripper mounting for variants with AKO EN ISO..., assembly instructions (operating manual with declaration of incorporation available online).