ELB 70-H050-H-N-N-2-H1G
ID 1488198
- Max. stroke: 50 mm
- Max. stroke: 50 mm
- Max. driving force: 150 N
Technical details
| Drive concept | Linear direct drive |
|---|---|
| Stroke [mm] | 50.0 |
| Max. driving force [N] | 150.0 |
| Nominal force [N] | 40.0 |
| Max. payload (horizontal) [kg] | 6.0 |
| Repeat accuracy [mm] | ± 0.01 |
| Max. speed [m/s] | 4.0 |
| Max. acceleration [m/s²] | 100.0 |
| Max. current [A] | 10.0 |
| Max. standstill current [A] | 2.6 |
| Min. ambient temperature [°C] | 10.0 |
| Max. ambient temperature [°C] | 40.0 |
| Weight [kg] | 2.08 |
| Clearance N (for moment load) [mm] | 34.1 |
| Stroke measuring system interface | HIPERFACE® |
| Length X [mm] | 225.0 |
| Width Y [mm] | 103.2 |
| Height Z [mm] | 46.5 |
| Moment Mx max. [Nm] | 79.0 |
| Moment My max. [Nm] | 54.0 |
| Moment Mz max. [Nm] | 27.0 |
| Force Fy max. [N] | 1210.0 |
| Force Fz max. [N] | 1210.0 |
| Force -Fz max. [N] | 1210.0 |
| H1 grease version | yes |
Dimensions and maximum loads
Travel times for 50/75 mm stroke*
Travel times for 125 mm stroke*
Dimensions and maximum loads
The indicated torques and forces are maximum values for static load in order to achieve the maximum lifespan of the product. Depending on use, increased loads are possible; please contact us to find out more!
Travel times for 50/75 mm stroke*
- X-axis:
- Stroke
- Y-axis:
- Travel times
Travel times for 125 mm stroke*
- X-axis:
- Stroke
- Y-axis:
- Travel times
General notes about the series
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Payload
is the weight of the total weight which is attached to the cantilever arm. Please consider that service life will shorten if the maximum payload is exceeded. SCHUNK cannot assume any warranty for this.
Geleiding
Kruisrolgeleiding
Aandrijving
Directe, lineaire aandrijving op basis van een 3-fase, elektronisch gecommuteerde en permanent bekrachtigde synchrone, lineaire gelijkstroommotor
Slagmeetsysteem
Contactloos, magnetisch meetsysteem met incrementele en absolute varianten; met HIPERFACE®-, 1Vss- en DRIVE-CLiQ-interfaces.
Profiel
Aluminium profiel met spelingvrij voorgespannen verbindingsrolgeleiding
Slede
Aluminium slede, primair onderdeel en leeskop van meetsysteem rechtstreeks ingebouwd
Levering
Veiligheidsinformatie (productspecifieke instructies online beschikbaar)
Aandrijvinsbesturing
Advies over parameterinstellingen voor regelaars van BOSCH (EcoDrive CS, IndraDrive en IndraDrive CS) en Siemens (Sinamics S120). Datasheets van motoren voor andere regelaars. Ondersteuning op verzoek.
Garantie
24 maanden
Kenmerken levensduur
op verzoek