DPZ-plus 80-1-IS
ID 1316293
- Hub pro Backe: 8 mm
- Öffnungskraft: 1330 N
- Max. Umgebungstemperatur: 90 °C
Technické údaje
| Hub pro Backe [mm] | 8.0 |
|---|---|
| Öffnungskraft [N] | 1330.0 |
| Öffnungskraft (bei Fingerlänge 0 mm) [N] | 1475.0 |
| Min. Federkraft [N] | 330.0 |
| Eigenmasse [kg] | 1.45 |
| Empfohlenes Werkstückgewicht [kg] | 4.5 |
| Zylindervolumen pro Doppelhub [cm³] | 108.0 |
| Min. Betriebsdruck [bar] | 4.0 |
| Max. Betriebsdruck [bar] | 6.5 |
| Nennbetriebsdruck [bar] | 6.0 |
| Min. Sperrluftdruck [bar] | 0.2 |
| Max. Sperrluftdruck [bar] | 0.5 |
| Schließzeit [s] | 0.08 |
| Öffnungszeit [s] | 0.05 |
| Max. zulässige Fingerlänge [mm] | 64.0 |
| Max. zulässige Masse pro Finger [kg] | 0.5 |
| Schutzart IP | 67 |
| Min. Umgebungstemperatur [°C] | 5.0 |
| Max. Umgebungstemperatur [°C] | 90.0 |
| Wiederholgenauigkeit [mm] | 0.01 |
| Reinraumklasse ISO 14644-1 | 5 |
| Zertifizierungsstand Reinraumklasse ISO 14644-1 | 1999 |
| Durchmesser D [mm] | 112.0 |
| Höhe Z [mm] | 71.2 |
| Moment Mx max. [Nm] | 45.0 |
| Moment My max. [Nm] | 71.0 |
| Moment Mz max. [Nm] | 40.0 |
| Max. Kraft axial Fz max. [N] | 1125.0 |
Die volle Greifkraft laut Datentabelle stellt sich unter Umständen erst nach einigen 100 Greifzyklen ein.
Dimensionen und max. Belastungen
Greifkraft Innengreifen
Dimensionen und max. Belastungen
Die angegebenen Momente und Kräfte sind statische Werte, gelten je Grundbacke und dürfen gleichzeitig auftreten. Die Belastungen dürfen zusätzlich zu dem durch die Greifkraft erzeugten Moment auftreten.
Greifkraft Innengreifen
- Osa X:
- Punkt P – Fingerlänge
- Osa Y:
- Greifkraft
General notes about the series
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Note – tightness
Please note that to achieve an IP 67 protection class, the gripper requires an additional hose for ventilation or a switchable air purge connection. For detailed information, please refer to the assembly and operating manual. Alternatively, a sinter filter (supplied) mounted on the air purge connection can prevent the penetration of dirt particles > 0.12 mm. However, this reduces the protection class to IP 54.
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Principe de fonctionnement
Cinématique à rampe forcée
Matériau du corps
Alliage d'aluminium anodisé
Matière des mors de base
Acier
Actionnement
pneumatique, par air comprimé filtré selon la norme ISO 8573-1:2010 [7:4:4].
Garantie
36 mois
Caractéristiques de la durée de vie
sur demande
Etendue de la livraison
Douilles de centrage, goupilles de centrage, joints toriques pour raccordement direct, notice de montage (la notice d'utilisation avec déclaration d'incorporation est disponible en ligne)
Maintien de la force de préhension
possible avec maintien mécanique de la force de préhension ou clapet anti-retour SDV-P