Machine loading: Its sealed design makes it possible for the EGU to also be used in harsh environmental conditions.
EGU
Universal gripper
Versatile 2-finger universal gripper for maximum workpiece variety with maximum process robustness
강력합니다. 유연성. 지능형.
범용 그리퍼 EGU
파지력 부스터를 지닌 스마트 범용 그리퍼.
SCHUNK의 범용 그리퍼 EGU는 열악한 환경에서도 배치 사이즈 1부터 시작하는 유연한 생산 공정에 이상적입니다. 자유롭게 네트워크로 연결할 수 있으며 다품종 생산 프로세스에 쉽게 통합할 수 있습니다. 그리핑 포스 유지 기능이 통합되어 있고 그리핑 포스를 높여주는 StrongGrip 모드가 있어 다양한 핸들링 작업을 안정적으로 처리할 수 있는 올라운더입니다. EGU는 PROFINET, EtherNet/IP, EtherCAT, IO-Link 및 Modbus RTU를 포함한 광범위한 인터페이스를 제공합니다. 주요 로봇 제조업체에 제공되는 PLC 기능 모듈과 플러그인 덕분에 소프트웨어 통합이 간단하며 추가 게이트웨이나 프로그래밍 워크로드가 필요하지 않습니다.
EGU 사용 중
Mechatronic grippers
Flexible and intelligent
The two grippers EGU and EGK combine all the advantages of mechatronic gripping and offer flexible workpiece handling due to their long and freely programmable jaw stroke with infinitely variable gripping force adjustment.
Advantages – Your benefits
- Versatile and productive
due to the long and freely programmable jaw stroke with continuous gripping force adjustment for flexible workpiece handling - Robust and reliable
with sealed design and proven sliding guidance especially suitable for the harsh ambient conditions of machine loading - Maximum process reliability
by avoiding workpiece loss due to integrated gripping force maintenance with loss detection - Always referenced
both in the event of an emergency stop and a power failure due to integrated absolute encoder - 100% gripping force without start-up distance
with almost constant gripping force over the entire finger length due to integrated spur gear - Minimal integration effort
compatible with the leading manufacturers on the market due to a wide range of communication interfaces, as well as PLC function blocks and robot plug-ins
Options and special information
- Gripping modes
The BasicGrip and StrongGrip gripping modes are available. With BasicGrip continuous operation of the motor and thus permanent re-gripping of the workpiece is possible. The gripping speed is automatically optimized for gripping force adjustment. With StrongGrip, the maximum gripping force is generated and then stored by the gripping force maintenance. Permanent regripping is possible within an adjustable time frame. In addition, defined pause times and maximum ambient temperatures must be taken into account in StrongGrip mode. Further details can be found in the operating manual. - Maintenance of gripping force
In the event of an emergency stop or a voltage drop, more than 80% of the originally applied gripping force can be reliably maintained due to a combination of an electric holding brake and the initial tension of the elastic element. If the gripping force and position maintenance is activated preventatively, 100% of the originally applied gripping force can be maintained. Overrun of the gripper fingers when removing the workpiece is a few millimeters and depends on the gripping force generated. Variants without gripping force maintenance are also available as an option. - Seal
The gripper has increased protection against the ingress of dust or liquids by default. The IP protection of the electronics is only given if the plug connectors have been mounted properly. The gearbox of the gripper is additionally protected by a seal on the main shaft. - Interface of the base jaws
When using the intermediate jaw, the interface of the base jaws corresponds to that of the universal gripper PGN-plus-P. This means that the extensive range of finger accessories for the PGN-plus-P can also be used for this gripper, taking into account the interfering contours, and the application limits that apply.