EGU 50-MB-N-SD
ID 1504557
- Stroke per jaw: 41 mm
- Min. gripping force: 210 N
- Max. gripping force: 300 N
- Power supply: 24 V
- Max. ambient temperature: 55 °C
Información técnica
| 죠당 스트로크 [mm] | 41.0 |
|---|---|
| 최소 파지력 [N] | 210.0 |
| 최대 파지력 [N] | 300.0 |
| 최대 허용 가능 핑거 길이 [mm] | 80.0 |
| 핑거당 최대 허용 무게 [kg] | 0.4 |
| 반복 정밀도(그리핑) [mm] | 0.02 |
| 반복 정밀도(위치 결정, 한방향) [mm] | 0.05 |
| 반복 정밀도(위치 결정, 양방향) [mm] | 0.15 |
| 폐쇄 시간 [s] | 0.8 |
| 개방 시간 [s] | 0.8 |
| 최대 속도(위치 결정) [mm/s] | 110.0 |
| 최대 가속도 [mm/s²] | 800.0 |
| 중량 [kg] | 1.47 |
| 최소 주위 온도 [°C] | 5.0 |
| 최대 주위 온도 [°C] | 55.0 |
| IP 보호 등급, 전자 장치 | 67 |
| IP 보호 등급, 가이드/베이스 죠 | 64 |
| 클린룸 클래스 ISO 14644-1:2015 | 4 |
| 길이 X [mm] | 122.0 |
| 너비 Y [mm] | 72.0 |
| 높이 Z [mm] | 88.0 |
| 정격 전압 [V] | 24.0 |
| 통신 인터페이스 | 모드버스 RTU |
| BasicGrip 공칭 전류 소비 [A] | 0.24 |
| BasicGrip 최대 전류 소비 [A] | 1.23 |
| 논리 공칭 전류 소비 [A] | 0.16 |
| 논리 최대 전류 소비 [A] | 0.2 |
| 모멘트 Mx 최대 [Nm] | 32.0 |
| 모멘트 My 최대 [Nm] | 35.0 |
| 모멘트 Mz 최대 [Nm] | 32.0 |
| 최대 축 포스 Fz 최대 [N] | 800.0 |
| 방진 버전 | 예 |
Dimensions and maximum loads
Maximum permitted finger projection
파지력 유지 포함 버전
파지력 유지 미포함 버전
최대 허용 핑거 추정
Dimensions and maximum loads
The indicated moments and forces are statical values, apply for each base jaw and may appear simultaneously. Loads may additionally occur to the moment produced by the gripping force itself.
Maximum permitted finger projection
파지력 유지 포함 버전
- Eje X:
- 핑거 길이
- Eje Y:
- 파지력
파지력 유지 미포함 버전
- Eje X:
- 핑거 길이
- Eje Y:
- 파지력
최대 허용 핑거 추정
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Repeat accuracy (gripping)
defined as the spread of the actual position during 100 consecutive closing or opening movements on a rigid workpiece or a fixed workpiece stop under constant conditions.
Repeat accuracy (positioning, unidirectional)
defined as the spread of the actual position per base jaw during 100 consecutive movements to a target position from the same direction under constant conditions.
Repeat accuracy (positioning, bi-directional)
defined as the distribution of the actual position per base jaw during 100 consecutive movements to a target position from both directions under constant conditions.
Finger length
is measured from the reference surface as the distance P in direction to the main axis.
Closing and opening times (positioning)
Closing and opening times are only the movement times of the fingers at max. speed, as well as max. acceleration with observance of the max. permissible mass per finger and refer to the traverse path per jaw and 50% of the nominal stroke.
Max. speed (positioning) and max. acceleration
is the arithmetic sum of the velocity and acceleration acting on each jaw.
Housing material
Aluminum alloy, anodized
Base jaw material
Steel, corrosion-protected
Warranty
24 months or 5 million cycles BasicGrip / 3 million cycles StrongGrip (one cycle consists of a complete gripping process: "Open gripper" and "Close gripper")
Scope of delivery
Gripper including safety information and accessory kit with centering sleeves for gripper and finger mounting. Product-specific instructions and software can be downloaded at schunk.com/downloads-manuals and schunk.com/downloads-software.