PGN-plus-P 40
ID 318448
- Course par mors : 2.5 mm
- Force à la fermeture: 180 N
- Force à l'ouverture: 200 N
- Température ambiant maxi.: 90 °C
Détails techniques
| 죠당 스트로크 [mm] | 2.5 |
|---|---|
| 폐쇄력 [N] | 180.0 |
| 개방력 [N] | 200.0 |
| 폐쇄력(핑거 길이 0mm) [N] | 198.0 |
| 개방력(핑거 길이 0mm) [N] | 255.0 |
| 중량 [kg] | 0.08 |
| 권고 공작물 중량 [kg] | 0.9 |
| 더블 스트로크당 실린더 용량 [cm³] | 4.0 |
| 최소 작동 압력 [bar] | 2.5 |
| 최대 작동 압력 [bar] | 8.0 |
| 정격 가동 압력 [bar] | 6.0 |
| 최소 에어 퍼지 압력 [bar] | 0.5 |
| 최대 에어 퍼지 압력 [bar] | 1.0 |
| 폐쇄 시간 [s] | 0.015 |
| 개방 시간 [s] | 0.015 |
| 최대 허용 가능 핑거 길이 [mm] | 65.0 |
| 핑거당 최대 허용 무게 [kg] | 0.12 |
| IP 보호등급 | 40 |
| 최소 주위 온도 [°C] | 5.0 |
| 최대 주위 온도 [°C] | 90.0 |
| 반복 정밀도 [mm] | 0.01 |
| 길이 X [mm] | 50.0 |
| 너비 Y [mm] | 25.0 |
| 높이 Z [mm] | 24.7 |
| 모멘트 Mx 최대 [Nm] | 10.0 |
| 모멘트 My 최대 [Nm] | 15.0 |
| 모멘트 Mz 최대 [Nm] | 5.0 |
| 최대 축 포스 Fz 최대 [N] | 650.0 |
寸法と最大荷重
最大許容フィンガー突起
파지력, O.D. 그리핑
파지력, I.D. 그리핑
最大許容フィンガー突起
寸法と最大荷重
示されたモーメントと荷重は固定値であり、各ベースジョーに作用し、同時発生することがあります。また､荷重は、把持力自体によって生成されたモーメントと別に発生することがあります。
最大許容フィンガー突起
파지력, O.D. 그리핑
- Axe X:
- 핑거 길이
- Axe Y:
- 파지력
파지력, I.D. 그리핑
- Axe X:
- 핑거 길이
- Axe Y:
- 파지력
最大許容フィンガー突起
Lmax は、最大許容フィンガー長に該当します。テクニカルデータ表をご参照ください。
- green
- 許容範囲
- grey
- 許容不可範囲
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Wedge gear with surface power transmission
Housing material
Aluminum
Base jaw material
Steel
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
36 months
Service life characteristics
on request
Scope of delivery
Brackets for proximity switches, centering sleeves, O-rings for direct connection, assembly instructions (operating manual with declaration of incorporation is available online)
Gripping force maintenance
possible by using the version with mechanical gripping force maintenance or pressure maintenance valve SDV-P