LGR 40-AS
ID 312979
Produits alternatifs :
- 開度: 90 °
- 閉じトルク: 13.8 Nm
- 最高周囲温度: 90 °C
Détails techniques
| 閉力 (フィンガー長 0 mm) [N] | 831.0 |
|---|---|
| ジョー当たりの開度 [°] | 90.0 |
| ジョー片側最大閉角度 [°] | 4.0 |
| 閉じトルク [Nm] | 13.8 |
| スプリングで保証された閉じトルク [Nm] | 3.0 |
| 重量 [kg] | 1.27 |
| 推奨ワーク重量 [kg] | 1.055 |
| ダブルストロークあたりのシリンダー容積 [cm³] | 24.0 |
| 最低作動圧力 [bar] | 4.0 |
| 最大作動圧 [bar] | 6.5 |
| 呼び作動圧力 [bar] | 6.0 |
| 閉時間 [s] | 0.21 |
| 開時間 [s] | 0.31 |
| 開閉時間（スプリング搭載時） [s] | 0.49 |
| 最大許容フィンガー長 [mm] | 80.0 |
| 最大許容重量／フィンガー [kg] | 0.22 |
| IP 保護等級 | 20 |
| 最低周囲温度 [°C] | 5.0 |
| 最高周囲温度 [°C] | 90.0 |
| 繰り返し精度 [mm] | 0.02 |
| モーメント Mx 最大 [Nm] | 8.0 |
| モーメント Mz最大 [Nm] | 6.0 |
| 最大軸方向力 Fz (最大) [N] | 130.0 |
Max. loads
Maximum permitted finger projection
Closing torque curve**
Maximum permitted finger projection
Max. loads
The indicated torques and forces are static values, apply for each base jaw, and may occur simultaneously.
Maximum permitted finger projection
Closing torque curve**
- Axe X:
- Opening angle
- Axe Y:
- Closing moment
Maximum permitted finger projection
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
General notes about the series
Closing moment
is the arithmetic sum of the individual moment applied to each jaw.
Finger length
is measured from the reference surface as the distance P in direction to the main axis.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Wedge-hook kinematics
Housing material
Aluminum alloy, anodized
Base jaw material
Steel
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
24 months
Scope of delivery
Centering elements, assembly, and operating instruction with manufacturer’s declaration.