RST-P 60-6-L
ID 314513
- Torque: 1.2 Nm
Technical details
| Drehwinkel [°] | 60.0 |
|---|---|
| Teilung | 6.0 |
| Drehrichtung | GUZS |
| Drehmoment [Nm] | 1.2 |
| Eigenmasse [kg] | 0.9 |
| Schutzart IP | 50 |
| Verriegelzeit [s] | 0.03 |
| Entriegelzeit [s] | 0.03 |
| Min. Umgebungstemperatur [°C] | 5.0 |
| Max. Umgebungstemperatur [°C] | 60.0 |
| Min. Betriebsdruck [bar] | 5.0 |
| Max. Betriebsdruck [bar] | 8.0 |
| Nennbetriebsdruck [bar] | 6.0 |
| Zylindervolumen pro Doppelhub [cm³] | 7.5 |
| Wiederholgenauigkeit [°] | 0.09 |
| Rundlauf Taktring [mm] | 0.02 |
| Planlauf Taktring [mm] | 0.02 |
| Parallelität Taktring [mm] | 0.04 |
| Anzahl hydr. Stoßdämpfer | 1.0 |
| L1 [mm] | 6.0 |
| L2 [mm] | 21.0 |
| Moment My max. [Nm] | 18.0 |
| Moment Mz max. [Nm] | 15.0 |
| Max. Kraft axial Fz max. [N] | 1950.0 |
| Max. Kraft radial Fr max. [N] | 1000.0 |
Max. Belastungen
Schwenkzeit
Max. Belastungen
Die angegebenen Momente und Kräfte sind statische Werte und dürfen gleichzeitig auftreten. Die Drosselung muss immer vorgenommen werden, damit die Drehbewegung schlag- und prellfrei erfolgen kann. Ansonsten kann sich die Lebensdauer verringern.
Schwenkzeit
- X-axis:
- Schwenkzeit
- Y-axis:
- Massenträgheit
- X-axis top:
- Zyklen pro Stunde
General notes about the series
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Drive ring
The position of the drive ring is always drawn in basic position. From here, the ring turns clockwise or anti-clockwise.
Cycle time
is the rotation time of pinion/flange around the nominal rotation angle. Valve switching times, hose filling times, or PLC reaction times are not included and are to be considered when cycle times are calculated.
Reference sensor
For monitoring the basic position, an inductive sensor can be attached, which will be actuated every 360°. It can be used for reference run or for checking if the control unit has counted correctly.
Swivel time depends on the payload
The shown diagrams are valid for nominal rotation angles, for the use with vertical swivel axis, or for centrical payloads with horizontal swivel axes, and at an operating pressure of 6 bar. The diagrams show the expected swivel time, and allows cycle per hour depending on the mass moments of inertia. The swiveling times need to be adjusted by using throttle valves, otherwise the life time could be reduced. We will be happy to help you designing other applications.
Housing material
Aluminum alloy, anodized
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Operating principle
Rack and pinion principle with back stroke freewheel
Scope of delivery
Centering elements, assembly, and operating instruction with manufacturer’s declaration.
Warranty
24 months