PGL-plus-P 10-ASC6-P-IN
IDnr. 1476713
- Stroke per jaw: 10 mm
- Closing force: 220 N
- Opening force: 220 N
- Nominal operating pressure: 6 bar
- Max. ambient temperature: 90 °C
Technische gegevens
with pre-assembled attachment kit for IN | yes |
---|---|
Precision version | yes |
Moment Mz max. [Nm] | 15.0 |
Opening force [N] | 220.0 |
Weight [kg] | 0.75 |
Min. ambient temperature [°C] | 5.0 |
Stroke per jaw [mm] | 10.0 |
Repeat accuracy [mm] | 0.03 |
Moment My max. [Nm] | 25.0 |
Closing force [N] | 220.0 |
Nominal operating pressure [bar] | 6.0 |
Max. permissible finger length [mm] | 100.0 |
Min. operating pressure [bar] | 5.5 |
Max. operating pressure [bar] | 6.5 |
Moment Mx max. [Nm] | 27.0 |
Closing time [s] | 0.04 |
Recommended workpiece weight [kg] | 1.1 |
Max. permissible weight per finger [kg] | 0.2 |
Min. air purge pressure [bar] | 0.5 |
Opening time [s] | 0.04 |
Cylinder volume per double stroke [cm³] | 13.0 |
Max. ambient temperature [°C] | 90.0 |
Max. axial force Fz max. [N] | 670.0 |
Protection class IP (without air purge) | 64 |
Max. air purge pressure [bar] | 1.0 |
Protection class IP (with air purge) | 67 |
Secured closing force in case of pressure loss | 176.0 |
Max. loads
Maximum permitted finger projection
Gripping force O.D. gripping
Maximum permitted finger projection
Max. loads
The indicated moments and forces are statical values, apply for each base jaw and may appear simultaneously. Loads may additionally occur to the moment produced by the gripping force itself.
Maximum permitted finger projection
Gripping force O.D. gripping
- X-as:
- Finger length
- Y-as:
- Gripping force
Maximum permitted finger projection
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Detectable workpiece difference
specifies the smallest distinguishable difference between two gripped workpieces. The value applies at 6 bar, 23 °C, finger length at distance P and operation without air purge. Deviating parameters can influence the accuracy.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Dual piston drive with gear rack and pinion synchronization
Housing material
Aluminum
Base jaw material
Steel
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
36 months
Scope of delivery
Gripper in the ordered variant, accessory kit (centering sleeves, O-rings for direct connection/detailed contents see operating manual) and safety information. Product-specific instructions can be downloaded at schunk.com/downloads-manuals.
Gripping force maintenance
via certified, safe gripping force maintenance version or conventionally via the variant with springs or via SDV-P pressure maintenance valve