JGP-P
功能
Funktionsschnittbild
Funktionsschnittbild
Der Kolben wird über Druckluft nach oben bzw. unten bewegt.
Die schrägen Wirkflächen des Keilhakens erzeugen dabei eine synchrone parallele Backenbewegung.
- 1
-
T-slot guidance
loadable, robust base jaw guidance for extremely long gripper fingers - 2
-
Base jaw
with standardized screw connection diagram for the connection of the workpiece-specific gripper fingers - 3
-
Bracket for sensors
Brackets for proximity switches and adjustable control cams in the housing - 4
-
Housing
is weight-optimized due to the use of high-strength aluminum alloy - 5
-
Centering and mounting possibilities
for universal assembly of the gripper - 6
-
Wedge-hook design
for high power transmission and minimal wear as a result of larger diagonal pull surfaces - 7
-
Piston
Maximum force through maximum surface of drive piston
Gripping force maintenance version AS/IS
유도성 근접 스위치로 모니터링하는 동안 제어 캠 설정
고객별 추가 구조물을 위해 커버 시트 아래에 장착 가능한 옵션
Gripping force maintenance version AS/IS
The mechanical gripping force maintenance device ensures that a minimum clamping force will be applied even if there is a drop in pressure. In the AS version this acts as a closing force, and in the IS version as an opening force. The image shows the AS version. The gripping force maintenance can also be used to increase the gripping force or for one-way gripping.
- 1
-
T-slot guidance
- 2
-
Base jaw
- 3
-
Bracket for sensors
- 4
-
Housing
- 5
-
Centering and mounting possibilities
- 6
-
Wedge-hook design
- 7
-
Piston
- 8
-
Gripping force maintenance
유도성 근접 스위치로 모니터링하는 동안 제어 캠 설정
유도성 근접 스위치를 사용한 모니터링은 64사이즈부터 표준으로 수행할 수 있습니다. 배송 시에는 제어 캠을 사용하여 "그리퍼 열림" 및 "그리퍼 닫힘" 위치가 사전 설정됩니다. 유도 센서는 별도로 주문해야 하며, 하우징 내부로 정지부까지 미끄러져 들어가 클램프로 고정됩니다.
예를 들어, "워크피스 잡음"과 같은 다른 위치를 모니터링하기 위해 두 제어 캠을 각 베이스 죠에 개별적으로 설정할 수 있습니다.
- 1
-
"그리퍼 닫힘" 위치용 제어 캠 사전 설정
- 2
-
"그리퍼 열림" 위치용 제어 캠 사전 설정
- 3
-
센서 고정용 클램핑 나사가 있는 홀더
- 4
-
조정된 전환점을 공정 신뢰성 높게 고정하기 위한 클램핑 나사
- 5
-
모든 전환점 설정용 조절 나사
고객별 추가 구조물을 위해 커버 시트 아래에 장착 가능한 옵션
배송 시 커버 시트는 그리퍼에 장착됩니다. 필요한 경우 제거할 수 있습니다. 커버 시트 아래에는 추가 기능을 구현할 수 있도록 고객 맞춤형 설계를 위한 스레드와 피팅이 있습니다.
- 1
-
추가 센터링 또는 워크피스 지지
- 2
-
커버 플레이트(제거 가능)
- 3
-
그리퍼에 부착된 외부 실린더가 있는 이젝터
적용 예시
적용 예시
사이클 타임이 최적화된 공작 기계의 로딩 및 언로딩. 로봇에 있는 2개의 그리퍼를 사용하여 사이클 타임에 최적화된 방식으로 공작 기계를 자동으로 로드하여 생산성을 높일 수 있습니다. 첫 번째 그리퍼가 완성된 부품을 내려 놓으면 이중 그리퍼에 내장된 블로우오프 노즐이 자동 클램핑 포스 블록에서 냉각수와 칩을 청소합니다. 그러면 두 번째 그리퍼는 머시닝되지 않은 부품을 바로 삽입할 수 있고, 머시닝 프로세스가 시작될 수 있습니다. 완성된 부품은 그 후 따로 배치되고, 머시닝되지 않은 다음 부품이 다시 픽업되며 동시에 공작물이 머시닝됩니다.
- 1
-
2-Finger-Parallelgreifer JGP-P
- 2
-
Kraftspannblock TANDEM PGS3