RST-D 87-12
Ident.-Nr. 315513
- Torque: 7.9 Nm
Información técnica
| Ángulo de giro [°] | 30.0 |
|---|---|
| Paso | 12.0 |
| Detección del giro | en ambos lados |
| Torque [Nm] | 7.9 |
| Peso [kg] | 2.9 |
| Clase de protección IP | 50 |
| Tiempo de bloqueo [s] | 0.1 |
| Tiempo de desbloqueo [s] | 0.1 |
| Temperatura ambiente mín. [°C] | 5.0 |
| Temperatura ambiente máx. [°C] | 60.0 |
| Presión de trabajo mín. [bar] | 4.0 |
| Presión de trabajo máx. [bar] | 8.0 |
| Presión nominal de servicio [bar] | 6.0 |
| Volumen del cilindro por carrera doble [cm³] | 19.0 |
| Precisión de repetición [°] | 0.06 |
| Anillo de ciclo de concentricidad [mm] | 0.02 |
| Anillo de ciclo de excentricidad [mm] | 0.02 |
| Paralelismo del anillo de cadencia [mm] | 0.04 |
| Número de amortiguadores hidráulicos | 2.0 |
| Longitud X [mm] | 136.0 |
| Anchura Y [mm] | 100.0 |
| Altura Z [mm] | 74.0 |
| Momento My máx. [Nm] | 40.0 |
| Momento Mz máx. [Nm] | 40.0 |
| Máx. fuerza axial Fz máx. [N] | 3400.0 |
| Máx. fuerza radial Fr máx. [N] | 1700.0 |
Dimensiones y cargas máximas
Tiempo de giro
Dimensiones y cargas máximas
Las fuerzas y pares indicados son valores estáticos que deben darse simultáneamente. Se debe regular el movimiento de giro para garantizar que no se produzcan impactos ni rebotes. De lo contrario, la vida útil del equipo puede disminuir.
Tiempo de giro
- Eje X:
- Tiempo de giro
- Eje Y:
- Momento de inercia de la masa
- Eje X superior:
- Ciclos por hora
General notes about the series
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Drive ring
The position of the drive ring is always drawn in basic position. From here, the ring turns clockwise or anti-clockwise.
Swiveling time
is the rotation time of pinion/flange around the nominal rotation angle. Valve switching times, hose filling times, or PLC reaction times are not included and are to be considered when cycle times are calculated.
Reference sensor
For monitoring the basic position, an inductive sensor can be attached, which will be actuated every 360°. It can be used for reference run or for checking if the control unit has counted correctly.
Swivel time depends on the payload
The shown diagrams are valid for nominal rotation angles, for the use with vertical swivel axis, or for centrical payloads with horizontal swivel axes, and at an operating pressure of 6 bar. The diagrams show the expected swivel time, and allows cycle per hour depending on the mass moments of inertia. The swiveling times need to be adjusted by using throttle valves, otherwise the life time could be reduced. We will be happy to help you designing other applications.
Total cycle time
The total cycle time consists of the swiveling time per cycle together with other required time intervals. See the operating manual for the exact calculation of the total cycle time.
Housing material
Aluminum alloy, anodized
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Operating principle
Rack and pinion principle with back stroke freewheel
Scope of delivery
Centering elements, safety information (product-specific instructions available online)
Warranty
24 months
Service life characteristics
on request