Co-act EGP-C 40-N-N-GoFa
ID 1468548
- Stroke per jaw: 6 mm
- Min. gripping force: 35 N
- Max. gripping force: 140 N
- Power supply: 24 V
- Max. total current: 2 A
- Max. ambient temperature: 55 °C
Technical details
| Compatible robot | ABB GoFa (CRB 15000) |
|---|---|
| Robot flange | Standard flange |
| Integrated sensors | yes, inductive in two directions |
| Length X [mm] | 93.8 |
| Width Y [mm] | 90.2 |
| Height Z [mm] | 123.0 |
| Stroke per jaw [mm] | 6.0 |
| Min. gripping force [N] | 35.0 |
| Max. gripping force [N] | 140.0 |
| Min. force per jaw [N] | 17.5 |
| Max. force per jaw [N] | 70.0 |
| Recommended workpiece weight [kg] | 0.7 |
| Max. permissible finger length [mm] | 50.0 |
| Max. permissible weight per finger [kg] | 0.08 |
| Repeat accuracy [mm] | 0.02 |
| Closing time [s] | 0.2 |
| Opening time [s] | 0.2 |
| Weight [kg] | 0.62 |
| Min. ambient temperature [°C] | 5.0 |
| Max. ambient temperature [°C] | 55.0 |
| IP protection class | 30 |
| Cable connector/cable end | 2 x M8 |
| Cable length L1 [mm] | 70.0 |
| Cable length L2 [mm] | 175.0 |
| Nominal voltage [V] | 24.0 |
| Nominal current [A] | 0.2 |
| Max. current [A] | 2.0 |
| Controller electronics | integrated |
| Communication interface | digital I/O |
| Number of digital inputs | 4.0 |
| Number of digital outputs | 2.0 |
| Moment Mx max. [Nm] | 1.5 |
| Moment My max. [Nm] | 2.0 |
| Moment Mz max. [Nm] | 4.0 |
| Max. axial force Fz max. [N] | 170.0 |
Dimensions and maximum loads
Maximum permitted finger projection
Gripping force
Maximum permitted finger projection
Dimensions and maximum loads
The indicated moments and forces are statical values, apply for each base jaw and may appear simultaneously. Loads may additionally occur to the moment produced by the gripping force itself.
Maximum permitted finger projection
Gripping force
- X-axis:
- Finger length
- Y-axis:
- Gripping force
Maximum permitted finger projection
Lmax is equivalent to the maximum permitted finger length, see the technical data table.
- green
- Permitted range
- grey
- Inadmissible range
시리즈에 관한 일반 참고 사항
파지력
P 거리에서 각 그리퍼 죠에 적용되는 파지력의 산술적인 합계입니다(그림 참조). 더 자세한 내용은 세부 기능 설명을 참고하십시오.
핑거 길이
주 축을 바라보는 P 거리처럼 참조면에서 측정됩니다.
반복 정밀도
100회 연속 스트로크 동안의 말단 위치 분포로 정의됩니다.
공작물 중량
중력 g로 인한 가속도에서 공작물 편차에 대응하는 0.1의 정지 마찰 계수와 2의 안전 계수를 갖춘 포스 맞춤 그리핑을 위해 계산됩니다. 끼워맞춤식 또는 포착 그리핑의 경우, 허용 공작물 중량이 훨씬 더 높습니다. 자세한 내용은 조립 및 작동 매뉴얼을 참조하십시오.
폐쇄 및 개방 횟수
애플리케이션별 그리퍼 핑거 없이 베이스 죠만 이동하는 시간입니다. PLC 반응 시간은 상기 시간에 포함되지 않으며 사이클 시간을 결정할 때 고려되어야 합니다.
작동 원리
랙과 피니언 원리
하우징 재료
유리 섬유 첨가 폴리아미드
베이스 죠 재료
강철
작동
브러시 없는 DC 서보모터를 통한 서보전동
보증
조립 및 작동 매뉴얼 참조
서비스 수명 특징
요청 시
제공 범위
어댑터 플랜지, 설치 재료 및 6각 소켓 렌치, 적합성과 법인 선언문을 포함한 조립 및 작동 매뉴얼, 안전 정보