PGL-plus-P 10-ASC4-P-IN
Ident.-Nr. 1476711
- Hub pro Backe: 10 mm
- Schließkraft: 145 N
- Öffnungskraft: 145 N
- Nennbetriebsdruck: 4 bar
- Max. Umgebungstemperatur: 90 °C
Technische Details
| Hub pro Backe [mm] | 10.0 |
|---|---|
| Schließkraft [N] | 145.0 |
| Öffnungskraft [N] | 145.0 |
| Abgesicherte Schließkraft bei Druckverlust [N] | 116.0 |
| Eigenmasse [kg] | 0.75 |
| Empfohlenes Werkstückgewicht [kg] | 0.72 |
| Zylindervolumen pro Doppelhub [cm³] | 13.0 |
| Min. Betriebsdruck [bar] | 3.5 |
| Nennbetriebsdruck [bar] | 4.0 |
| Max. Betriebsdruck [bar] | 6.5 |
| Min. Sperrluftdruck [bar] | 0.5 |
| Max. Sperrluftdruck [bar] | 1.0 |
| Schließzeit [s] | 0.04 |
| Öffnungszeit [s] | 0.04 |
| Max. zulässige Fingerlänge [mm] | 100.0 |
| Max. zulässige Masse pro Finger [kg] | 0.2 |
| Schutzart IP (ohne Sperrluft) | 64 |
| Schutzart IP (mit Sperrluft) | 67 |
| Min. Umgebungstemperatur [°C] | 5.0 |
| Max. Umgebungstemperatur [°C] | 90.0 |
| Wiederholgenauigkeit [mm] | 0.03 |
| Moment Mx max. [Nm] | 27.0 |
| Moment My max. [Nm] | 25.0 |
| Moment Mz max. [Nm] | 15.0 |
| Max. Kraft axial Fz max. [N] | 670.0 |
| Präzisions-Version | ja |
| mit vormontiertem Anbausatz für IN | ja |
Max. Belastungen
Maximal zulässige Auskragung
Greifkraft Außengreifen
Maximal zulässige Auskragung
Max. Belastungen
Die angegebenen Momente und Kräfte sind statische Werte, gelten je Grundbacke und dürfen gleichzeitig auftreten. Die Belastungen dürfen zusätzlich zu dem durch die Greifkraft erzeugten Moment auftreten.
Maximal zulässige Auskragung
Greifkraft Außengreifen
- X-Achse:
- Fingerlänge
- Y-Achse:
- Greifkraft
Maximal zulässige Auskragung
Lmax entspricht der maximal zulässigen Fingerlänge, siehe technische Datentabelle.
- green
- Zulässiger Bereich
- grey
- Unzulässiger Bereich
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Detectable workpiece difference
specifies the smallest distinguishable difference between two gripped workpieces. The value applies at 6 bar, 23 °C, finger length at distance P and operation without air purge. Deviating parameters can influence the accuracy.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Dual piston drive with gear rack and pinion synchronization
Housing material
Aluminum
Base jaw material
Steel
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
36 months
Scope of delivery
Gripper in the ordered variant, accessory kit (centering sleeves, O-rings for direct connection/detailed contents see operating manual) and safety information. Product-specific instructions can be downloaded at schunk.com/downloads-manuals.
Gripping force maintenance
via certified, safe gripping force maintenance version or conventionally via the variant with springs or via SDV-P pressure maintenance valve