LGZ 32
ID 312933
Alternativní produkty:
- Zdvih na čelist: 4 mm
- Zavírací síla: 450 N
- Otevírací síla: 540 N
- Max. okolní teplota: 90 °C
Technické údaje
| Hub pro Backe [mm] | 4.0 |
|---|---|
| Schließkraft [N] | 450.0 |
| Öffnungskraft [N] | 540.0 |
| Schließkraft (bei Fingerlänge 0 mm) [N] | 479.0 |
| Öffnungskraft (bei Fingerlänge 0 mm) [N] | 531.0 |
| Eigenmasse [kg] | 0.32 |
| Empfohlenes Werkstückgewicht [kg] | 2.25 |
| Zylindervolumen pro Doppelhub [cm³] | 21.0 |
| Min. Betriebsdruck [bar] | 2.0 |
| Max. Betriebsdruck [bar] | 8.0 |
| Nennbetriebsdruck [bar] | 6.0 |
| Schließzeit [s] | 0.02 |
| Öffnungszeit [s] | 0.02 |
| Schließ-/Öffnungszeit mit Feder [s] | 0.15 |
| Max. zulässige Fingerlänge [mm] | 60.0 |
| Max. zulässige Masse pro Finger [kg] | 0.08 |
| Schutzart IP | 40 |
| Min. Umgebungstemperatur [°C] | 5.0 |
| Max. Umgebungstemperatur [°C] | 90.0 |
| Wiederholgenauigkeit [mm] | 0.02 |
| Moment Mx max. [Nm] | 1.2 |
| Moment My max. [Nm] | 4.5 |
| Moment Mz max. [Nm] | 2.0 |
| Max. Kraft axial Fz max. [N] | 120.0 |
Max. Belastungen
Greifkraft Außengreifen
Greifkraft Innengreifen
Max. Belastungen
Die angegebenen Momente und Kräfte sind statische Werte, gelten je Grundbacke und dürfen gleichzeitig auftreten. Die Belastungen dürfen zusätzlich zu dem durch die Greifkraft erzeugten Moment auftreten.
Greifkraft Außengreifen
- Osa X:
- Punkt P – Fingerlänge
- Osa Y:
- Greifkraft
Greifkraft Innengreifen
- Osa X:
- Punkt P – Fingerlänge
- Osa Y:
- Greifkraft
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Wedge-hook kinematics
Housing material
Aluminum alloy, anodized
Base jaw material
Steel
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
24 months
Scope of delivery
Centering elements, assembly, and operating instruction with manufacturer’s declaration.