MPC 100
ID 1343466
- Slag per klem: 10 mm
- Sluitkracht: 170 N
- Openingskracht: 170 N
- Max. omgevingstemperatuur: 60 °C
Technical details
| Slag per klem [mm] | 10.0 |
|---|---|
| Sluitkracht [N] | 170.0 |
| Openingskracht [N] | 170.0 |
| Sluitkracht (bij vingerlengte van 0 mm) [N] | 183.0 |
| Openingskracht (bij vingerlengte van 0 mm) [N] | 183.0 |
| Gewicht [kg] | 0.34 |
| Aanbevolen gewicht werkstuk [kg] | 0.85 |
| Cilindervolume per dubbele slag [cm³] | 8.0 |
| Min. werkdruk [bar] | 2.0 |
| Max. werkdruk [bar] | 8.0 |
| Nominale werkdruk [bar] | 6.0 |
| Sluitingstijd [s] | 0.09 |
| Openingstijd [s] | 0.09 |
| Max. toegelaten vingerlengte [mm] | 40.0 |
| Max. toegestaan gewicht per vinger [kg] | 0.13 |
| IP-beschermklasse | 30 |
| Min. omgevingstemperatuur [°C] | 5.0 |
| Max. omgevingstemperatuur [°C] | 60.0 |
| Rondloopnauwkeurigheid [mm] | 0.02 |
| Lengte X [mm] | 92.0 |
| Breedte Y [mm] | 46.0 |
| Hoogte Z [mm] | 31.0 |
| Moment Mx max. [Nm] | 8.0 |
| Moment My max. [Nm] | 8.0 |
| Moment Mz max. [Nm] | 8.0 |
| max. axiale kracht Fz max. [N] | 250.0 |
Afmetingen en maximaal toegelaten belasting
Maximum permitted finger projection
Grijpkracht
Maximaal toegelaten vingeraanzet
Afmetingen en maximaal toegelaten belasting
De opgegeven waarden voor moment en kracht zijn statische waarden, gelden voor elke basisklem en kunnen tegelijkertijd voorkomen. Naast het moment dat door de grijpkracht zelf wordt gegeneerd, kunnen er nog extra lasten optreden.
Maximum permitted finger projection
Grijpkracht
- X-axis:
- Vingerlengte
- Y-axis:
- Grijpkracht
Maximaal toegelaten vingeraanzet
Lmax is gelijk aan de maximaal toegestane vingerlengte. Zie de tabel met technische gegevens
- green
- Toegelaten bereik
- grey
- Niet-toelaatbaar bereik
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
synchronized double piston
Warranty
12 months
Service life characteristics
on request
Maintenance and repair
is not envisaged. The gripper is maintenance-free. In the event of a defect, the entire gripper is replaced.
Scope of delivery
Accessory kit with centering pins, assembly instructions (operating manual with declaration of incorporation is available online)
Gripping force maintenance
possible with pressure maintenance valve SDV-P