PGN-plus 200-2-AS-V
Universal gripper
ID 39371455
This product is a legacy product.
Alternative products:
Universal gripper PGN-plus, Size: 200, pneumatic, with gripping force maintenance: AS, in a high-temperature version
- Stroke per jaw: 14 mm
- Closing force: 6250 N
- Max. ambient temperature: 130 °C
Technical details
Stroke per jaw [mm] | 14.0 |
---|---|
Closing force [N] | 6250.0 |
Closing force (with finger lengths of 0 mm) [N] | 7072.0 |
Min. spring force [N] | 1600.0 |
Weight [kg] | 7.5 |
Recommended workpiece weight [kg] | 23.5 |
Cylinder volume per double stroke [cm³] | 495.0 |
Min. operating pressure [bar] | 4.0 |
Max. operating pressure [bar] | 6.5 |
Nominal operating pressure [bar] | 6.0 |
Min. air purge pressure [bar] | 0.5 |
Max. air purge pressure [bar] | 1.0 |
Closing time [s] | 0.3 |
Opening time [s] | 0.6 |
Closing/opening time with spring [s] | 0.5 |
Max. permissible finger length [mm] | 200.0 |
Max. permissible weight per finger [kg] | 6.5 |
IP protection class | 40 |
Min. ambient temperature [°C] | 5.0 |
Max. ambient temperature [°C] | 130.0 |
Repeat accuracy [mm] | 0.02 |
Cleanroom class ISO 14644-1 | 5 |
Length X [mm] | 234.0 |
Width Y [mm] | 100.0 |
Height Z [mm] | 141.0 |
Moment Mx max. [Nm] | 180.0 |
Moment My max. [Nm] | 200.0 |
Moment Mz max. [Nm] | 140.0 |
Max. axial force Fz max. [N] | 5000.0 |
High-temperature version | yes |
It may take a few 100 gripping cycles until the full gripping force (as indicated in the data table) will be available.
尺寸和最大载荷
最大允许手指投影
最大允许手指投影
尺寸和最大载荷
所示力矩和力为静态值,适用于每个基爪,且可能会同时出现。除抓取力自身产生的力矩外,还可能产生负载。
最大允许手指投影
最大允许手指投影
曲线适用于行程型 1。其他型号的曲线必须按照最大允许基爪长度平行偏移。
- green
- 允许的范围
- grey
- 不允许的范围
产品系列的常规说明
抓取力
在距离 P(请参见插图)处施加到每个机械手夹爪的抓取力的算术和。
手指长度
沿主轴方向,从距基准面距离 P 处测得。 在达到额定工作压力之前,适用最大允许手指长度。压力较高时,手指长度必须成比例减小至额定工作压力。
重复精度
定义为 100 个连续行程后极限位置分布。
工件重量
采用摩擦系数 0.1 和安全系数(防止由于重力加速 g 工件滑落) 2 计算压入配合抓取。如果是适形或捕获式抓取,可抓取工件重量则大很多。
闭合/打开时间
仅是基爪的移动时间,不含特定应用的机械手手指。不包括阀门开关时间、软管注入时间或 PLC 反应时间,但是计算周期时必须考虑这些时间。
洁净室等级 14644-1:1999
5
工作原理
表面输电的楔齿
外壳材料
铝
基爪材料
钢
启动
气动,带符合 ISO 8573-1:2010 [7:4:4] 的过滤压缩空气。
保修期
36 个月
使用寿命特性
根据要求
标配范围
所订购的机械手、附件包(定心套筒,用于直接连接的 O 型圈/详细内容请参见操作手册)和安全信息。对应的产品说明书,可以前往 schunk.com/downloads-manuals 下载。
抓取力保持
可通过配有机械抓取力安全装置或 SDV-P 保压阀的变型实现