ELB 70-H050-H-N-N-2
ID 1409339
- 最大行程: 50 mm
- 最大行程: 50 mm
- 最大传动力: 150 N
技术细节
| 传动概念 | 线性电机驱动 |
|---|---|
| 行程 [mm] | 50.0 |
| 最大传动力 [N] | 150.0 |
| 额定力 [N] | 40.0 |
| 最大有效载荷（水平） [kg] | 6.0 |
| 重复精度 [mm] | ± 0.01 |
| 最大速度 [m/s] | 4.0 |
| 最大加速度 [m/s²] | 100.0 |
| 最大电流 [A] | 10.0 |
| 停止时最大电流 [A] | 2.6 |
| 最低环境温度 [°C] | 10.0 |
| 最高环境温度 [°C] | 40.0 |
| 重量 [kg] | 2.08 |
| 间隙 N（力矩负载） [mm] | 34.1 |
| 行程测量系统接口 | HIPERFACE® |
| 长度 X [mm] | 225.0 |
| 宽度 Y [mm] | 103.2 |
| 高度 Z [mm] | 46.5 |
| 力矩 Mx max. [Nm] | 79.0 |
| 力矩 My max. [Nm] | 54.0 |
| 力矩 Mz max. [Nm] | 27.0 |
| 力 Fy max. [N] | 1210.0 |
| 力 Fz max. [N] | 1210.0 |
| 力 -Fz max. [N] | 1210.0 |
Dimensions and maximum loads
50/75 mm 行程的移动时间*
125 mm 行程的移动时间*
Dimensions and maximum loads
The indicated torques and forces are maximum values for static load in order to achieve the maximum lifespan of the product. Depending on use, increased loads are possible; please contact us to find out more!
50/75 mm 行程的移动时间*
- X 轴:
- 行程
- Y 轴:
- 行程时间
125 mm 行程的移动时间*
- X 轴:
- 行程
- Y 轴:
- 行程时间
General notes about the series
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Payload
is the weight of the total weight which is attached to the cantilever arm. Please consider that service life will shorten if the maximum payload is exceeded. SCHUNK cannot assume any warranty for this.
Guidance
Cross roller guidance
Drive
Linear direct drive based on a 3-phase, electronically commutated and permanently excited AC synchronous liner motor
Stroke measuring system
Contactless, magnetic measuring system with incremental and absolute variants; with HIPERFACE®, 1Vss and DRIVE-CLiQ interfaces.
Profile
Aluminum profile with pre-loaded junction roller guide that is free from play
Slide
Aluminum slide, primary part and measuring system reading head directly integrated
Scope of delivery
Safety information (product-specific instructions available online)
Drive controller
Consultation on parameter settings for drive controllers from BOSCH (EcoDrive CS, IndraDrive and IndraDrive CS) and Siemens (Sinamics S120). Provision of motor data sheets for other drive controllers. Commissioning support on request.
Warranty
24 months
Service life characteristics
on request