KGG 280
Gripper for small components
ID 340313
Gripper for small components KGG, Size: 280, pneumatic
- Stroke per jaw: 60 mm
- Closing force: 540 N
- Opening force: 670 N
- Max. ambient temperature: 90 °C
Technical details
Closing force [N] | 540.0 |
---|---|
Stroke per jaw [mm] | 60.0 |
Max. operating pressure [bar] | 8.0 |
Opening force [N] | 670.0 |
Nominal operating pressure [bar] | 6.0 |
Weight [kg] | 4.2 |
Recommended workpiece weight | 2.7 |
Opening time [s] | 0.25 |
Closing time [s] | 0.29 |
Max. permissible weight per finger [kg] | 2.0 |
Min. ambient temperature [°C] | 5.0 |
Max. ambient temperature [°C] | 90.0 |
Repeat accuracy [mm] | 0.1 |
Moment Mx max. [Nm] | 16.0 |
Max. axial force Fz max. [N] | 3000.0 |
Min. operating pressure [bar] | 2.5 |
Moment My max. [Nm] | 70.0 |
Moment Mz max. [Nm] | 50.0 |
IP protection class | 30 |
Max. permissible finger length [mm] | 160.0 |
Cylinder volume per double stroke [cm³] | 170.0 |
Cleanroom class ISO 14644-1 | 7 |
Length X [mm] | 280.0 |
Height Z [mm] | 80.0 |
Width Y [mm] | 72.0 |
Opening force (with finger lengths of 0 mm) [N] | 742.0 |
Closing force (with finger lengths of 0 mm) [N] | 597.0 |
It may take a few 100 gripping cycles until the full gripping force (as indicated in the data table) will be available.
尺寸和最大载荷
最大允许手指投影
抓取力,外夹抓取
抓取力,内撑抓取
最大允许手指投影
尺寸和最大载荷
所示力矩和力为静态值,适用于每个基爪,且可能会同时出现。除抓取力自身产生的力矩外,还可能产生负载。
最大允许手指投影
抓取力,外夹抓取
- X-axis:
- P 点 - 手指长度
- Y-axis:
- 抓取力
抓取力,内撑抓取
- X-axis:
- P 点 - 手指长度
- Y-axis:
- 抓取力
最大允许手指投影
Lmax 等于最大允许手指长度。请参见技术参数表。
- green
- 允许的范围
- grey
- 不允许的范围
产品系列的常规说明
抓取力
在距离 P(请参见插图)处施加到每个机械手夹爪的抓取力的算术和。
手指长度
沿主轴方向,从距基准面距离 P 处测得。 在达到额定工作压力之前,适用最大允许手指长度。压力较高时,手指长度必须成比例减小至额定工作压力。
重复精度
定义为 100 个连续行程后极限位置分布。
工件重量
采用摩擦系数 0.1 和安全系数(防止由于重力加速 g 工件滑落) 2 计算压入配合抓取。如果是适形或捕获式抓取,可抓取工件重量则大很多。
闭合/打开时间
仅是基爪的移动时间,不含特定应用的机械手手指。不包括阀门开关时间、软管注入时间或 PLC 反应时间,但是计算周期时必须考虑这些时间。
工作原理
直接传动基爪,采用齿条和小齿轮原理同步
外壳材料
铝合金,阳极氧化
基爪材料
铝合金,阳极氧化
启动
气动,带符合 ISO 8573-1:2010 [7:4:4] 的过滤压缩空气。
保修期
24 个月
使用寿命特性
根据要求
标配范围
所订购的机械手、附件包(定心套筒,用于直接连接的 O 型圈/详细内容请参见操作手册)和安全信息。对应的产品说明书,可以前往 schunk.com/downloads-manuals 下载。
抓取力保持
可以配备 SDV-P 压力保持阀