ELG
Funktion
Funktionsschnittbild
Funktionsschnittbild
Ein Servomotor treibt über einen Zahnriemen den Kugelgewindetrieb an, welcher die mit den Spindelmuttern und Profilschienen verbundenen Grundbacken linear bewegt.
- 1
-
Antrieb
Servomotoren zahlreicher Hersteller adaptierbar - 2
-
Kinematik
hohe Belastbarkeit und Genauigkeit durch bewährte Kombination von Kugelgewindetrieb und Zahnriemen - 3
-
Profilschienenführung
hochbelastbare, spielarme Grundbackenführung für große Fingerlängen - 4
-
Grundbacke
zur Adaption der werkstückspezifischen Greiferfinger
Individuell konfigurierbarer Hub
Finger version
Synchronization
Gripper mounting
Position clamping
Lateral mounting options
Weight optimization
Cover plates
Bellow
Drive motors
Individuell konfigurierbarer Hub
Der Hub pro Backe kann kundenindividuell zwischen 100 mm und 400 mm pro Backe millimetergenau konfiguriert werden. (Bei der Baugröße 10 ist der Hub auf 300 mm begrenzt)
- 1
-
Variant with 100 mm stroke per jaw
- 2
-
Variant with 400 mm stroke per jaw
Finger version
The gripper is available in two finger versions. In addition to the basic variant for short finger lengths, a variant with a long finger length can also be configured for corresponding applications.
- 1
-
Short finger length with two guiding carriages per base jaw
- 2
-
Long finger length with four guiding carriages per base jaw
Synchronization
The gripper can be configured as a synchronous and asynchronous variant. In the synchronous variant, the two base jaws are jointly controlled by a servomotor, with the jaw movement being synchronized by a counter-rotating ball screw. With the asynchronous variant, the two base jaws can be controlled independently and separately from each other. In this variant, one base jaw each is connected to one of the two required servomotors via the ball screw and the toothed belt.
- 1
-
Synchronous version
- 2
-
Asynchronous version
Gripper mounting
The gripper offers different options for mounting on robots or gantries.
- 1
-
One-piece adapter plate (gripper side)
- 2
-
Adapter plate, complete (gripper side + blank)
- 3
-
Adapter plate, complete for screw connection according to EN ISO 9409
Position clamping
The electric holding brake prevents the movement of the ball screw, thereby clamping the position of the base jaws. Two brakes are required for the asynchronous variant. One fast switching module (ROBA®-brake-checker) is required for each holding brake (ROBA-stop®). This is included in the scope of delivery of the gripper.
- 1
-
Electric holding brake
Lateral mounting options
Optional mounting options on the gripper for customized additional attachments such as cameras, sensor distributors or blow-out nozzles. This option cannot be combined with the "weight-optimized design" option.
- 1
-
Connection thread for additional attachment
- 2
-
Fit for centering pins
Weight optimization
Cutouts in the sidewalls reduce the weight of the gripper by up to 15%. This option cannot be combined with the option "side mounting options".
- 1
-
Cutouts for weight reduction
Cover plates
The cover plates close the gripper on the attachment side. This protects the gripper from external influences at this point. The motor connections are cut out accordingly.
- 1
-
Cover plates
- 2
-
Motor connection
Bellow
The bellow closes the gripper on the side of the base jaws. It is only available in combination with the cover plate option and it improves the protection of the gripper against environmental influences.
- 1
-
Bellows cover
- 2
-
Cover plates
Drive motors
Different drive motors can be adapted to the gripper to enable flexible control and simple connection to existing control concepts.
- 1
-
Motor-specific attachment kit (always included in the scope of delivery)
- 2
-
Bosch or Siemens motors (optionally pre-assembled)
- 3
-
additional motors: see configurator (not included in the scope of delivery)
- 4
-
motors not included in the configurator on request
Application example
Application example
Application-specific long-stroke gripper for handling washing machines in the end-of-line packaging process
- 1
-
Application-specific long-stroke gripper ELG
- 2
-
Attachment fingers
- 3
-
Feeding of the washing machine
- 4
-
Feeding of the packaging material
- 5
-
Further transport of the packed washing machine
