SDV-P 04
Válvula de manutenção de pressão
ID 403130
Válvula de manutenção de pressão SDV-P
- Fio: G1/8"
Specifiche tecniche
| Thread | G1/8" |
|---|---|
| Nominal diameter (DN) [mm] | 4.0 |
| Flow rate, hose Ø 6mm [l/min] | 200.0 |
| Flow rate, hose Ø 8mm [l/min] | 250.0 |
| Flow rate, hose Ø 10mm [l/min] | 340.0 |
| Recommended hose diameter [mm] | 6.0 |
| Pressure loss, input/output [bar] | 0.5 |
| Min. operating pressure [bar] | 2.0 |
| Max. operating pressure [bar] | 10.0 |
| IP protection class | 67 |
| Min. ambient temperature [°C] | -10.0 |
| Max. ambient temperature [°C] | 80.0 |
| Valve switching time [ms] | 15.0 |
| Weight [kg] | 0.1 |
The possible volume of flow through the valve depends on the used pneumatic hoses. The table shows the flow rate according to the used pneumatic hose (reference pressure 6 bar). In order to alleviate the choice of the SDV-P, SCHUNK has defined a recommended hose diameter. This is relevant for the allocation suggested by SCHUNK.
In general, possible additional combinations can be determined as follows:
1. Calculation of the required flow rate for the variant of the components:
required flow rate Q [l/min]
Fluid consumption per double stroke V [cm3]
Closing or opening time t [s]
Q = 0.21*(V/t)
2. Selection of the right SDV-P: the flow rate of the SDV-P must be larger or equal to the calculated required flow rate Q. If this is not taken into consideration, the cycle time may increase.
In general, possible additional combinations can be determined as follows:
1. Calculation of the required flow rate for the variant of the components:
required flow rate Q [l/min]
Fluid consumption per double stroke V [cm3]
Closing or opening time t [s]
Q = 0.21*(V/t)
2. Selection of the right SDV-P: the flow rate of the SDV-P must be larger or equal to the calculated required flow rate Q. If this is not taken into consideration, the cycle time may increase.
モデルシリーズに関する一般注意事項
流量
SDV-P および SDV-P-E タイプでは、バルブを通過可能な流量は、使用するホースに依存します。下の表に、使用するホースと流量の関係を示します (基準圧力 6 bar)。 直径はホースの外径です。対応する内径は、メーカーによって僅かに異なることがありますが、バルブへの影響は僅かです。SDV-P-E-P タイプの場合の流量はホースに依存しません
バルブ切り換え時間
他の負荷を考慮しない純粋の SDV-P バルブの切り換え時間。バルブ切り換え時間を、それぞれのグリッパーの開閉時間などの負荷側の移動時間に加算する必要があります。
圧力損失、入力/出力
入力圧力と、スプリング式チェックバルブ通過後の出力圧力との差である圧力損失を表します。出力にアクチュエーターを接続する構成では、この圧力損失を考慮に入れる必要があるかもしれません。
手動クイック通気
SDV-P-E および SDV-P-E-P のタイプは、手動式クイックリリース通気機能を備えています。圧縮空気ホースを取り外さずに、接続されているアクチュエーターの通気を行うことができます (セットアップ時や非常停止発生後のシステム再起動時など)。
ハウジングの材質
アルミニウム
作動
空圧式、フィルターを通した圧縮空気、ISO 8573-1:2010 [7:4:4] に準拠。
保証
24 カ月