Moduli singoli NSE3
Funzionamento
Functie NSE3 138
Functie NSE3 138
- 1
-
Optional cone seal
Voor het beschermen van de wisselinterface - 2
-
Patented dual stroke system
A patented dual stroke system between piston and clamping slide ensures maximum pull-down forces - 3
-
Turbo function
For amplification of the pull-down force - 4
-
Large contact surfaces
For transmitting the pull-down and holding forces - 5
-
Completely sealed system
Therefore absolutely maintenance-free - 6
-
Large flat surface
For best support and highest rigidity - 7
-
Monitoring of the clamping slide position "open condition" and "locked condition"
Via dynamic pressure possible - 8
-
Flat seal to protect the interface during machining
Dampens the placment of the workpiece or clamping pallet - 9
-
Cover plugs for mounting screws
Therefore no accumulation of coolant or chips possible - 10
-
Sliding bearings in the force flow
For maximum pull-down forces with a long service life - 11
-
Lower-lying countersunk screws
For easy cleaning of the flat surface
Comparison: Pull-down Force Spring Clamping and Turbo Function
100 % compatibel met de NSE plus -generatie
De plug kan worden vervangen door een conusafdichting
Centrering via korte conus
Locking via clamping slides
Easy joining – more user-friendly
Integrated turbo function
Rolling friction between piston and clamping slide
Lower-lying countersunk screws
Control of the quick-change pallet system
스테인리스강으로 제작된 압력 스프링
스테인리스강 재질 – 긴 서비스 수명
동적 압력을 통해 클램핑 슬라이드 위치 모니터링 – 개방 상태
동적 압력을 통해 클램핑 슬라이드 위치 모니터링 – 잠김 상태
NSE3 138-V1 – 통합형 비틀림 방지 보호 V1이 있는 퀵 체인지 팔레트 모듈
NSE-T3 138 – 3세대 툼스톤 모듈
Comparison: Pull-down Force Spring Clamping and Turbo Function
When using the turbo function, only an air pulse is needed to increase the pull-down force of the spring force clamping by up to 3.5 times.
- 1
-
Aandrijfkracht van de veerkrachtopspanning
Dit gebeurt door de perslucht in de module of het klemstation te verwijderen. - 2
-
Aandrijfkracht van de turbofunctie
Korte luchtpuls in de zuigerkamer van de veren. - 3
-
Neerhaalkracht van de veerkrachtopspanning
Dit loopt bedraagt max. 8 kN en is het resultaat van de veerkracht nadat de perslucht is verwijderd. - 4
-
Neerhaalkracht met turbofunctie
De trekkracht wordt met de NSE3 138 maxi door de luchtpuls verhoogd tot 28 kN. - 5
-
Y-as
Toont de factor waarmee de trekkracht wordt verhoogd. - 6
-
X-as
Bedieningsdruk van de turbofunctie om aan te geven hoe de trekkracht bij toenemende druk wordt verhoogd.
100 % compatibel met de NSE plus -generatie
De snelwissel-palletmodules van de NSE3-generatie zijn 100 % compatibel met de NSE plus-generatie. Hierdoor zijn de alle modules 1:1 uitwisselbaar.
De plug kan worden vervangen door een conusafdichting
Alle snelwissel-palletmodules uit de NSE3-serie zijn standaard geschikt voor integratie van een conusafdichting. De standaardplug kan op een later moment eenvoudig door een conusafdichting worden vervangen.
Centrering via korte conus
Het SCHUNK snelwissel-palletsysteem kenmerkt zich door de nauwkeurige korte conus centrering in combinatie met de vormsluitende en zelfborgende vergrendeling.
Locking via clamping slides
Large contact surfaces between clamping slides and clamping pin ensure a low surface pressure, resulting in a long service life.
Easy joining – more user-friendly
Insertion radii on the clamping pin enable quick and safe joining even at a tilt angle and in case of eccentricity.
Benefit: More user friendly for manual and automatic loading.
Integrated turbo function
In order to increase the pull-down force, the quick-change pallet module is additionally actuated with compressed air. Compared to the pure clamping force achived via spring force, the turbo function influences the pull-down force by a factor 3.5 (max. 28,000 N). By using the active turbo function, achieving higher cutting parameters during the machining process is possible.
- 1
-
Spring force
Stainless, fatigue-resistant pressure springs. - 2
-
Additional force
Resulting from the turbo function.
Rolling friction between piston and clamping slide
In order to further increase the pull-down force, plain bearing bushings are integrated in the piston for bearing the cylinder pin. Therefore the efficiency is increased and wear minimizes at the same time.
Lower-lying countersunk screws
Countersunk screws are used in the lower-lying flat surface, allowing an easy cleaning of the flat surface.
Control of the quick-change pallet system
The modules are actuated via lateral or bottom air connections.
Benefit: The module is versatile in installation.
스테인리스강으로 제작된 압력 스프링
서비스 수명을 극대화하기 위해 모든 구동 스프링은 약화가 없는 스테인리스강으로 만들어졌습니다.
스테인리스강 재질 – 긴 서비스 수명
모든 기능 구성품은 강화 스테인리스강으로 제작되었습니다.
동적 압력을 통해 클램핑 슬라이드 위치 모니터링 – 개방 상태
- 1
-
탈기
클램핑 슬라이드가 보어 구멍 위로 정렬되어 있지 않으므로 압축 공기가 빠져나갈 수 있습니다. - 2
-
동적 압력
클램핑 슬라이드가 보어 구멍 위로 정렬되어 있으므로 압축 공기가 빠져나갈 수 없습니다.
동적 압력을 통해 클램핑 슬라이드 위치 모니터링 – 잠김 상태
- 1
-
동적 압력
클램핑 슬라이드가 보어 구멍 위로 정렬되어 있으므로 압축 공기가 빠져나갈 수 없습니다. - 2
-
탈기
클램핑 슬라이드가 보어 구멍 위로 정렬되어 있지 않으므로 압축 공기가 빠져나갈 수 있습니다.
NSE3 138-V1 – 통합형 비틀림 방지 보호 V1이 있는 퀵 체인지 팔레트 모듈
새로운 세대의 단일 모듈 NSE3 138-V1 또한 수정된 버전이며 단일 팔레트의 사용에 대해 NSE3 138과 동일한 이점을 제공합니다.
NSE-T3 138 – 3세대 툼스톤 모듈
툼스톤 모듈 NSE-T3 138은 또한 새로운 세대의 모듈입니다. 극단적인 강성의 모듈로 더욱 높은 기계가공 파라미터를 달성합니다.
이점: 더욱 높은 풀다운 포스 씰 링의 선택 사항 사용, 긴 서비스 수명
