ERT 12-40-B-N-D-2
ID 1482031
- Coppia: 1.4 Nm
- Corrente nominale: 0.96 A
- Alimentazione elettrica: 560 V
Specifiche tecniche
| Coppia nominale [Nm] | 1.4 |
|---|---|
| Coppia massima [Nm] | 4.17 |
| Numero di giri max. [1/min] | 600.0 |
| Momento max. di inerzia della massa ammissibile [kgm²] | 0.07 |
| Precisione di ripetibilità [°] | 0.01 |
| Planarità [mm] | 0.02 |
| Concentricità [mm] | 0.02 |
| Peso [kg] | 2.7 |
| Temperatura ambiente min. [°C] | 5.0 |
| Temperatura ambiente max. [°C] | 40.0 |
| Classe di protezione IP | 40 |
| Freno di arresto momento [Nm] | 1.4 |
| Forza Fx max [N] | 700.0 |
| Forza Fz max [N] | 700.0 |
| Lunghezza X [mm] | 181.0 |
| Larghezza Y [mm] | 135.0 |
| Altezza Z [mm] | 64.0 |
| Coppia My max. [Nm] | 24.0 |
| Tensione del circuito intermedio [V] | 560.0 |
| Corrente nominale [A] | 0.96 |
| Corrente max. [A] | 3.27 |
| Sistema trasduttori | Encoder (assoluto) |
| Segnale di uscita | DRIVE-CLiQ |
| Certificazione SIL | 2 |
Dimensioni e carichi massimi
Diagramma del tempo di rotazione
Diagramma del tempo di rotazione IP54
Dimensioni e carichi massimi
Le forze e le coppie indicate si riferiscono ai valori massimi in caso di sollecitazione singola. Se si applicano più forze e/o momenti contemporaneamente, i valori individuali saranno più bassi.
Diagramma del tempo di rotazione
- Asse X:
- Tempo di rotazione
- Asse Y:
- Momento di inerzia della massa
- Asse X superiore:
- Cicli all'ora
Diagramma del tempo di rotazione IP54
- Asse X:
- Tempo di rotazione
- Asse Y:
- Momento di inerzia della massa
- Asse X superiore:
- Cicli all'ora
General notes about the series
Stroke measuring system
Motor-feedback system for absolute measurement, single-turn version, with the HIPERFACE®, HIPERFACE DSL® and DRIVE-CLiQ interfaces
Swiveling times
The swiveling times are purely the times when the module moves from rest position to rest position. Delays caused by the PLC or the drive controller are not included and to be taken into consideration when determining cycle times. Load-dependent rest periods may have to be included in the cycle time.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Repeat accuracy
The repeat accuracy is defined as the spread of the target position after 100 consecutive positioning cycles.
Ambient conditions
The modules are primarily designed for the use in clean to slightly contaminated environments. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases.
Safety notes
Caution: Magnetic field! This particularly applies for persons with implanted medical devices, such as pacemakers, hearing aids, etc.
Nominal currents
The rated currents can be permanently actuated. With regard to all the currents which are ranging above the nominal current up to the maximum current, the notes of the individual product documentation has to be respected.
Housing material
Cast aluminum, powder-coated
Drive
Torque motor, 3-phase
Stroke measuring system
Contactless, magnetic measuring system in absolute version; with HIPERFACE® and DRIVE-CLiQ interfaces.
Drive controller
Consultation on parameter settings for drive controllers from BOSCH (EcoDrive CS, IndraDrive and IndraDrive CS) and Siemens (Sinamics S120). Provision of motor data sheets for other drive controllers. Commissioning support on request.
Scope of delivery
Accessory kit with centering sleeves, safety information (product-specific instructions are available online)
Warranty
24 months
Service life characteristics
on request