PZV 64
ID 304000
- 죠당 스트로크: 4 mm
- 폐쇄력: 570 N
- 개방력: 630 N
- 최대 주위 온도: 90 °C
기술 세부 정보
| 죠당 스트로크 [mm] | 4.0 |
|---|---|
| 폐쇄력 [N] | 570.0 |
| 개방력 [N] | 630.0 |
| 폐쇄력(핑거 길이 0mm) [N] | 678.0 |
| 개방력(핑거 길이 0mm) [N] | 712.0 |
| 중량 [kg] | 0.5 |
| 권고 공작물 중량 [kg] | 2.8 |
| 더블 스트로크당 실린더 용량 [cm³] | 25.0 |
| 최소 작동 압력 [bar] | 2.0 |
| 최대 작동 압력 [bar] | 8.0 |
| 정격 가동 압력 [bar] | 6.0 |
| 최소 에어 퍼지 압력 [bar] | 0.5 |
| 최대 에어 퍼지 압력 [bar] | 1.0 |
| 폐쇄 시간 [s] | 0.02 |
| 개방 시간 [s] | 0.02 |
| 최대 허용 가능 핑거 길이 [mm] | 64.0 |
| 핑거당 최대 허용 무게 [kg] | 0.18 |
| IP 보호등급 | 40 |
| 최소 주위 온도 [°C] | 5.0 |
| 최대 주위 온도 [°C] | 90.0 |
| 반복 정밀도 [mm] | 0.01 |
| 직경 D [mm] | 76.0 |
| 높이 Z [mm] | 41.3 |
| 모멘트 Mx 최대 [Nm] | 20.0 |
| 모멘트 My 최대 [Nm] | 25.0 |
| 모멘트 Mz 최대 [Nm] | 10.0 |
| 최대 축 포스 Fz 최대 [N] | 500.0 |
치수 및 최대 로드
파지력, O.D. 그리핑
파지력, I.D. 그리핑
치수 및 최대 로드
표시된 모멘트와 포스는 정적인 값이고 각 베이스 죠에 적용되며 동시에 나타날 수 있습니다. 부하가 파지력 자체에 의해서 생성되는 모멘트에 추가로 발생할 수 있습니다.
파지력, O.D. 그리핑
- X축:
- 포인트 P - 핑거 길이
- Y축:
- 파지력
파지력, I.D. 그리핑
- X축:
- 포인트 P - 핑거 길이
- Y축:
- 파지력
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Wedge-hook kinematics
Housing material
Aluminum alloy, anodized
Base jaw material
Steel
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
36 months
Service life characteristics
on request
Scope of delivery
Brackets for proximity switches, centering sleeves, O-rings for direct connection, assembly instructions (operating manual with declaration of incorporation is available online)
Gripping force maintenance
possible with pressure maintenance valve SDV-P