ELB 70-H050-H-B-N-N
ID 315401
- 최대 스트로크: 50 mm
- 최대 스트로크: 50 mm
- 최대 추진력: 150 N
Technical details
| Drive concept | Linear direct drive |
|---|---|
| Stroke [mm] | 50.0 |
| Max. driving force [N] | 150.0 |
| Nominal force [N] | 40.0 |
| Max. payload (horizontal) [kg] | 6.0 |
| Repeat accuracy [mm] | ± 0.01 |
| Max. speed [m/s] | 4.0 |
| Max. acceleration [m/s²] | 100.0 |
| Max. current [A] | 10.0 |
| Max. standstill current [A] | 2.6 |
| Min. ambient temperature [°C] | 10.0 |
| Max. ambient temperature [°C] | 40.0 |
| Weight [kg] | 2.36 |
| Clearance N (for moment load) [mm] | 34.1 |
| Stroke measuring system interface | HIPERFACE® |
| Actuation holding brake | pneumatic |
| Static holding force break [N] | 350.0 |
| Axial play, brake [mm] | 0.3 |
| Length X [mm] | 230.3 |
| Width Y [mm] | 127.7 |
| Height Z [mm] | 62.0 |
| Moment Mx max. [Nm] | 79.0 |
| Moment My max. [Nm] | 54.0 |
| Moment Mz max. [Nm] | 27.0 |
| Force Fy max. [N] | 1210.0 |
| Force Fz max. [N] | 1210.0 |
| Force -Fz max. [N] | 1210.0 |
| Version with holding brake | yes |
Dimensions and maximum loads
Travel times for 50/75 mm stroke*
Travel times for 125 mm stroke*
Dimensions and maximum loads
The indicated torques and forces are maximum values for static load in order to achieve the maximum lifespan of the product. Depending on use, increased loads are possible; please contact us to find out more!
Travel times for 50/75 mm stroke*
- X-axis:
- Stroke
- Y-axis:
- Travel times
Travel times for 125 mm stroke*
- X-axis:
- Stroke
- Y-axis:
- Travel times
General notes about the series
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Payload
is the weight of the total weight which is attached to the cantilever arm. Please consider that service life will shorten if the maximum payload is exceeded. SCHUNK cannot assume any warranty for this.
가이드
크로스 롤러 가이드
드라이브
3상 전자적으로 정류되고 영구적으로 여기되는 AC 동기 리니어 모터에 기반한 리니어 다이렉트 드라이브
스트로크 측정 시스템
증분 및 절대적인 이형이 있는 비접촉식 마그네틱 측정 시스템이며 HIPERFACE®, 1Vss 및 DRIVE-CLiQ 인터페이스가 있습니다.
프로필
움직임 없는 사전 로드 접합 롤러 가이드의 알루미늄 프로필
슬라이드
알루미늄 슬라이드, 기본 부품 및 판독 헤드가 직접 통합된 측정 시스템
제공 범위
안전 정보(제품별 지침은 온라인에서 제공)
드라이브 컨트롤러
BOSCH(EcoDrive CS, IndraDrive 및 IndraDrive CS)와 Siemens(Sinamics S120)의 드라이브 컨트롤러에 대한 매개변수 설정에 대한 컨설팅. 다른 구동 컨트롤러에 대한 모터 데이터 시트 제공. 요청에 따라 시운전 지원.
보증
24개월
서비스 수명 특징
요청 시