arrow calendar cartcheck checkmark close configure contact cube danger download external_link facebook globeimage info instagram jobfinder linkedin logo_claim logout mail menuminus navigation pin play plus refresh rss searchshaft success twitteruserwarning wechat x-twitterxing youku youtube zoom
Zmień kraj, aby zobaczyć informacje o produktach, usługach i osobach kontaktowych dla konkretnych lokalizacji.
SPG 100 Ilustracja analogiczna

SPG 100

Chwytak do dużych obciążeń

Identyfikator 302121

Chwytak do dużych obciążeń SPG, Rozmiar: 100, pneumatyczna

  • Skok na szczękę: 100 mm
  • Siła zamykająca: 10000 N
  • Siła otwierająca: 11480 N
  • Maks. temperatura otoczenia: 90 °C
Skok na szczękę [mm] 100.0
Siła zamykająca [N] 10000.0
Siła otwierająca [N] 11480.0
Siła zamykania (długość palca 0 mm) [N] 10920.0
Siła otwierania (długość palca 0 mm) [N] 12536.0
Masa [kg] 35.0
Zalecana masa detalu [kg] 50.0
Objętość cylindra na podwójny skok [cm³] 4600.0
min. ciśnienie robocze [bar] 2.0
Maks. ciśnienie robocze [bar] 8.0
Znamionowe ciśnienie robocze [bar] 6.0
Min. ciśnienie powietrza oczyszczającego [bar] 0.5
Maks. ciśnienie powietrza oczyszczającego [bar] 1.0
Czas zamykania [s] 1.5
Czas otwierania [s] 1.5
Maks. dopuszczalna długość palca [mm] 500.0
Maks. dopuszczalna masa na palec [kg] 15.0
Stopień ochrony IP 30
Min. temperatura otoczenia [°C] 5.0
Maks. temperatura otoczenia [°C] 90.0
Powtarzalność [mm] 0.1
Długość X [mm] 436.0
Szerokość Y [mm] 196.0
Wysokość Z [mm] 191.9
Moment Mx maks. [Nm] 250.0
Moment My maks. [Nm] 300.0
Moment Mz maks. [Nm] 250.0
Maks. siła osiowa Fz maks. [N] 6000.0
Aby uzyskać pełną siłę chwytania (określonej w tabeli z danymi technicznymi), potrzebne może być wykonanie około 100 cykli chwytania.
Czasy otwierania i zamykania można dodatkowo zredukować, montując zawory szybkiego odpowietrzania na przyłączach pneumatycznych. Należy jednak przy tym zachować ostrożność, aby nie dopuścić do uderzania lub obijania się szczęk podczas ruchu.

General notes about the series

Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).

Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.

Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.

Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.

Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.

Housing material
Aluminum alloy, anodized

Base jaw material
Aluminum alloy, anodized

Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].

Warranty
24 months

Service life characteristics
on request

Scope of delivery
Gripper in the ordered variant, accessory kit (centering sleeves, O-rings for direct connection/detailed contents see operating manual) and safety information. Product-specific instructions and software can be downloaded at schunk.com/downloads-manuals.

Gripping force maintenance
corresponding version with ID 0302120 includes a pressure maintenance valve SDV-P 07 in the scope of delivery. The version with ID 0302121 is supplied without pressure maintenance valve, but can be retrofitted.