PHL-W 25-060-S
ID 308135
Alternativní produkty:
- Zdvih na čelist: 60 mm
- Zavírací síla: 620 N
- Max. okolní teplota: 90 °C
Technické údaje
Course par mors [mm] | 60.0 |
---|---|
Force à la fermeture [N] | 620.0 |
Force de fermeture (avec longueurs de doigt de 0 mm) [N] | 630.0 |
Force du ressort min. [N] | 120.0 |
Poids [kg] | 2.21 |
Volume du cylindre par course double [cm³] | 210.0 |
Pression d'utilisation min. [bar] | 4.0 |
Pression d'utilisation maximale [bar] | 6.5 |
Pression d'utilisation nominale [bar] | 6.0 |
Temps de fermeture [s] | 0.2 |
Temps d'ouverture [s] | 0.44 |
Longueur de doigt max. admissible [mm] | 180.0 |
Poids de doigt max. admissible [kg] | 1.0 |
Indice de protection IP | 41 |
Température ambiante mini. [°C] | 5.0 |
Température ambiant maxi. [°C] | 90.0 |
Répétabilité [mm] | 0.02 |
Longueur X [mm] | 325.0 |
Largeur Y [mm] | 74.0 |
Hauteur Z [mm] | 59.7 |
Moment Mx max. [Nm] | 33.0 |
Moment My max. [Nm] | 120.0 |
Moment Mz max. [Nm] | 46.0 |
Force axiale max. Fz max. [N] | 1000.0 |
Dimensions et charges max.
Maximum permitted finger projection
Dépassement maximum autorisé
Dimensions et charges max.
Les moments et les forces indiqués correspondent à des valeurs statiques et s'appliquent à chacun des mors de base et peuvent survenir simultanément. Ils peuvent s’ajouter au moment produit par la force de préhension elle-même.
Maximum permitted finger projection
Dépassement maximum autorisé
Lmax correspond à la longueur de doigt maximale admissible, voir tableau des caractéristiques techniques.
- green
- Plage admissible
- grey
- Plage non admissible
General notes about the series
Gripping force
is the arithmetic sum of the individual force applied to each jaw at distance P (see illustration).
Finger length
is measured from the reference surface as the distance P in direction to the main axis. The maximum permissible finger length applies until the nominal operating pressure is achieved. With higher pressures, the finger length must be reduced proportionally to the nominal operating pressure.
Repeat accuracy
is defined as a distribution of the end Position for 100 consecutive strokes.
Workpiece weight
is calculated for force-fit gripping with a coefficient of static friction of 0.1 and a safety factor of 2 against workpiece slippage at acceleration due to gravity g. For form-fit or capture gripping, there are significantly higher permissible workpiece weights.
Closing and opening times
are movement times of the base jaws only, without application-specific gripper fingers. Valve switching times, hose fill times, or PLC reaction times are not included, and are to be considered when cycle times are calculated.
Operating principle
Double piston rack and pinion principle
Housing material
Aluminum (extruded profile)
Base jaw material
Aluminum alloy, anodized
Guidance
Profiled rail guide
Actuation
pneumatic, with filtered compressed air as per ISO 8573-1:2010 [7:4:4].
Warranty
24 months
Service life characteristics
on request
Scope of delivery
Gripper in the ordered variant, accessory kit (centering sleeves, O-rings for direct connection/detailed contents see operating manual) and safety information. Product-specific instructions can be downloaded at schunk.com/downloads-manuals.
Gripping force maintenance
possible by using the version with mechanical gripping force maintenance or pressure maintenance valve SDV-P