B 110-SRS-M-2525
- 最大ストローク: 5120 mm
- 最大駆動力: 6000 N
技術的詳細
| 最大行程 H [mm] | 5120.0 |
|---|---|
| 最大传动力 [N] | 6000.0 |
| 重复精度 [mm] | ± 0.03 |
| 最大总长度 [mm] | 5600.0 |
| 最大速度 [m/s] | 1.25 |
| 最大加速度 [m/s²] | 20.0 |
| 最低环境温度 [°C] | 0.0 |
| 最高环境温度 [°C] | 80.0 |
| 包括滑块在内的底板自重 [kg] | 12.5 |
| 每 100 mm 行程的额外质量 [kg] | 1.4 |
| 滑块重量 [kg] | 5.8 |
| 滑动板长度 [mm] | 320.0 |
| 导轨系统 | 滚子导轨 |
| 滚动直径 [mm] | 28.0 |
| 传动概念 | 主轴驱动 |
| 怠速扭矩 [Nm] | 1.0 |
| 惯性矩 [kgm²] | 2.25E-4 |
| 主轴直径 [mm] | 25.0 |
| 轴距 [mm] | 25 |
| 最大主轴速度 [1/min] | 3000.0 |
| 长度 X [mm] | 480.0 |
| 宽度 Y [mm] | 110.0 |
| 高度 Z [mm] | 135.0 |
| 力矩 Mx max. [Nm] | 300.0 |
| 力矩 My max. [Nm] | 600.0 |
| 力矩 Mz max. [Nm] | 450.0 |
| 力 Fy max. [N] | 2000.0 |
| 力 Fz max. [N] | 5000.0 |
| 力 -Fz max. [N] | 2500.0 |
带噪音阻尼 (SAG) 的 SCHUNK 标准主轴支架，每 2 个 SAG 会减少 10 mm 的最大行程。
请注意，主轴的惯性矩为一米。
Dimensions and maximum loads
Spindle supports**
Dimensions and maximum loads
The indicated forces and moments are maximum values for individual loading. If several forces and/or moments are applied at the same time, the maximum permitted individual values will be lower.
Spindle supports**
- X 軸:
- Axis length
- Y 軸:
- Speed of rotation
General notes about the series
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Max. stroke
is the maximum permissible stroke. Acceleration and braking distances or possible overrun must be taken into consideration.
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Acceleration and speed
The values specified are the maximum values of the units without loading. The actual accelerations and speeds for your application must be designed separately and can deviate from the maximum values.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Operating principle
Choice of toothed belt or ball screw spindle drive
Drive
servomotors of different providers can be trouble-free adapted
Profile
Extruded aluminum profile with plastic cover strip
Slide
Aluminum slide with a brush seal
Scope of delivery
Assembly and operating manual with declaration of incorporation
Warranty
24 months