ELB 70-H125-D-B-N-2-H1G
ID 1488351
- 最大ストローク: 125 mm
- 最大ストローク: 125 mm
- 最大駆動力: 150 N
技術的詳細
| Concepto de accionamiento | Accionamiento directo lineal |
|---|---|
| Carrera [mm] | 125.0 |
| Fuerza de accionamiento máx. [N] | 150.0 |
| Fuerza nominal [N] | 40.0 |
| Carga útil máx. (horizontal) [kg] | 6.0 |
| Precisión de repetición [mm] | ± 0.01 |
| Velocidad máx. [m/s] | 4.0 |
| Aceleración máx. [m/s²] | 100.0 |
| Corriente máx. [A] | 10.0 |
| Corriente de parada máx. [A] | 2.6 |
| Temperatura ambiente mín. [°C] | 10.0 |
| Temperatura ambiente máx. [°C] | 40.0 |
| Peso [kg] | 2.96 |
| Holgura N (para carga de momentos) [mm] | 34.1 |
| Interfaz del sistema de medición de carrera | DRIVE-CLiQ |
| Accionamiento freno de retención | neumática |
| Freno de fuerza de retención estática [N] | 350.0 |
| Juego axial, freno [mm] | 0.3 |
| Longitud X [mm] | 355.3 |
| Anchura Y [mm] | 127.7 |
| Altura Z [mm] | 62.0 |
| Momento Mx máx. [Nm] | 101.0 |
| Momento My máx. [Nm] | 68.0 |
| Momento Mz máx. [Nm] | 34.0 |
| Fuerza Fy máx. [N] | 1480.0 |
| Fuerza Fz máx. [N] | 1480.0 |
| Fuerza Fz máx. [N] | 1480.0 |
| Modelo con DRIVE-CLiQ | sí |
| Versión de grasa H1 | sí |
| Versión con freno de retención | sí |
Dimensiones y cargas máximas
Tiempos de desplazamiento para una carrera de 50/75 mm*
Tiempos de desplazamiento para una carrera de 125 mm*
Dimensiones y cargas máximas
Los torques de apriete y las fuerzas indicados son valores máximos para carga estática, con el fin de prolongar al máximo la vida útil del producto. Dependiendo del uso, se permiten cargas superiores. Póngase en contacto con nosotros para saber más.
Tiempos de desplazamiento para una carrera de 50/75 mm*
- X 軸:
- Carrera
- Y 軸:
- Tiempo de desplazamiento
Tiempos de desplazamiento para una carrera de 125 mm*
- X 軸:
- Carrera
- Y 軸:
- Tiempo de desplazamiento
General notes about the series
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Payload
is the weight of the total weight which is attached to the cantilever arm. Please consider that service life will shorten if the maximum payload is exceeded. SCHUNK cannot assume any warranty for this.
Guidance
Cross roller guidance
Drive
Linear direct drive based on a 3-phase, electronically commutated and permanently excited AC synchronous liner motor
Stroke measuring system
Contactless, magnetic measuring system with incremental and absolute variants; with HIPERFACE®, 1Vss and DRIVE-CLiQ interfaces.
Profile
Aluminum profile with pre-loaded junction roller guide that is free from play
Slide
Aluminum slide, primary part and measuring system reading head directly integrated
Scope of delivery
Safety information (product-specific instructions available online)
Drive controller
Consultation on parameter settings for drive controllers from BOSCH (EcoDrive CS, IndraDrive and IndraDrive CS) and Siemens (Sinamics S120). Provision of motor data sheets for other drive controllers. Commissioning support on request.
Warranty
24 months
Service life characteristics
on request