ELB 70-H050-D-N-N-2-H1G
ID 1488312
- Max. zdvih: 50 mm
- Max. zdvih: 50 mm
- Max. hnací síla: 150 N
Technické údaje
| Koncepce pohonu | Lineární přímý pohon |
|---|---|
| Zdvih [mm] | 50.0 |
| Max. hnací síla [N] | 150.0 |
| Jmenovitá síla [N] | 40.0 |
| Max. jmenovité zatížení (vodorovné) [kg] | 6.0 |
| Opakovatelná přesnost [mm] | ± 0.01 |
| Max. rychlost [m/s] | 4.0 |
| Max. zrychlení [m/s²] | 100.0 |
| Max. proud [A] | 10.0 |
| Max. stacionární proud [A] | 2.6 |
| Min. okolní teplota [°C] | 10.0 |
| Max. okolní teplota [°C] | 40.0 |
| Vlastní hmotnost [kg] | 2.08 |
| Vzdálenost N (pro momentové zatížení) [mm] | 34.1 |
| Rozhraní systému měření zdvihu | DRIVE-CLiQ |
| Délka X [mm] | 225.0 |
| Šířka Y [mm] | 103.2 |
| Výška Z [mm] | 46.5 |
| Max. moment Mx [Nm] | 79.0 |
| Max. moment My [Nm] | 54.0 |
| Max. moment Mz [Nm] | 27.0 |
| Max. síla Fy [N] | 1210.0 |
| Max. síla Fz [N] | 1210.0 |
| Max. síla Fz [N] | 1210.0 |
| Verze s DRIVE-CLiQ | ano |
| Verze maziva H1 | ano |
Rozměry a maximální zatížení
Časy pojezdu zdvih 50/75 mm *
Časy pojezdu zdvih 125 mm *
Rozměry a maximální zatížení
Uvedené momenty a síly jsou maximální hodnoty pro statické zatížení, aby se dosáhlo maximální životnosti výrobku. V závislosti na použití je možné zvýšit zatížení; kontaktujte nás a dozvíte se více!
Časy pojezdu zdvih 50/75 mm *
- Osa X:
- Zdvih
- Osa Y:
- Provozní doba
Časy pojezdu zdvih 125 mm *
- Osa X:
- Zdvih
- Osa Y:
- Provozní doba
General notes about the series
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Payload
is the weight of the total weight which is attached to the cantilever arm. Please consider that service life will shorten if the maximum payload is exceeded. SCHUNK cannot assume any warranty for this.
Guidance
Cross roller guidance
Drive
Linear direct drive based on a 3-phase, electronically commutated and permanently excited AC synchronous liner motor
Stroke measuring system
Contactless, magnetic measuring system with incremental and absolute variants; with HIPERFACE®, 1Vss and DRIVE-CLiQ interfaces.
Profile
Aluminum profile with pre-loaded junction roller guide that is free from play
Slide
Aluminum slide, primary part and measuring system reading head directly integrated
Scope of delivery
Safety information (product-specific instructions available online)
Drive controller
Consultation on parameter settings for drive controllers from BOSCH (EcoDrive CS, IndraDrive and IndraDrive CS) and Siemens (Sinamics S120). Provision of motor data sheets for other drive controllers. Commissioning support on request.
Warranty
24 months
Service life characteristics
on request