SCHUNK는 로봇 액세서리는 물론 그리핑, 터닝, 리니어 모듈에 대한 유도, 자기 및 광학 모니터링 센서의 광범위한 포트폴리오를 제공합니다. 위치에 사용되는 간단한 비접촉 스위치 외에도 조정 가능한 히스테리시스와 2개의 조정 가능한 스위칭 포인트를 가진 프로그래머블 센서가 있습니다. 아날로그 출력이 있는 SCHUNK 센서는 여러 다른 위치 또는 다른 측정 절차에 적합합니다.
The analog sensor APS-Z80 is used to query the jaw position of SCHUNK grippers. It inductively detects the course of an inclined plane and gives back a continuous output signal.
The analog MMS 22-A magnetic sensor is used for monitoring the status of SCHUNK grippers. It detects the approach of a magnet without contact and returns a continuous output signal.
The FPS system is used to determine up to five jaw positions of a SCHUNK gripper. For this purpose, the magnetic sensor of the FPS system detects a magnet installed in the gripper. The FPS system can be teached in five areas of the gripper and digitally displays the area in which the current jaw position is located.
Inductive proximity switches are used to scan the current status of automation components. They are offered by SCHUNK in versions IN and INK. The version IN is directly pluggable or has a molded cable with plug connector. The INK version is suitable for direct wiring. It has a molded cable with an open end.
A magnetic switch is used for monitoring the status of automation components. They detect the approach of a magnet without contact and above a certain switching value, they put out a digital signal.
A magnetic switch is used for monitoring the status of automation components. They detect the approach of a magnet without contact and above a certain switching value, they put out a digital signal.
A magnetic switch is used for monitoring the status of automation components.They detect the magnets fixed inside the component without contact. In addition to further process data, the sensor outputs the process of the magnetic field via the IO-Link interface.
A magnetic switch is used to monitor the status of automation components. They detect the approach of a magnet without contact and above a certain switching value, they put out a digital value. The switching value can be programmed.
ATEX magnetic switches are used to monitor the status of automation components in potentially explosion hazard atmospheres They detect the approach of a magnet without contact and above a certain switching value, they put out a digital signal. The switching value can be programmed.
A magnetic switch is used to monitor the status of automation components. They detect the approach of a magnet without contact and above a certain switching value, they put out a digital value. The switching value can be programmed.
A magnetic switch is used for monitoring the status of automation components. They detect the approach of a magnet without contact and above a certain switching value, they put out a digital signal.
Reed switches are mechanical switches that react to the presence of magnetic fields (magnets). They are often used as a low-cost alternative to electronic magnetic switches.
Reed switches are mechanical switches that react to the presence of magnetic fields (magnets). They are often used as a low-cost alternative to electronic magnetic switches.
The analog sensor BIP is used to monitor the jaw position of SCHUNK grippers. It inductively detects the position of the position transducer and returns a continuous output signal.
The SST sensor tester enables the rapid testing and adjustment of inductive sensors, magnetic switches and reed contacts. The necessary power is supplied by a 9 V compound battery.
For connecting many SCHUNK sensors (IN(K)/MMS(K) 22/MMS(K)22-PI1 etc.), and collecting respective sensor signals. In the versions 2-fold (V2), 4-fold (V4) and 8-fold (V8). V2-4P sensor distributor for connecting MMS22-PI2 and MMS-P22 sensors for dividing a four-pin M8 connector into two three-pin M8 connectors.
