B 100-ZSS-40AT10-200
- 최대 스트로크: 7420 mm
- 추진력 버전: 40 AT 10
- 최대 추진력: 2800 N
기술 세부 정보
| 최대 스트로크 H [mm] | 7420.0 |
|---|---|
| 최대 추진력 [N] | 2800.0 |
| 반복 정밀도 [mm] | ± 0.08 |
| 최대 총 길이 [mm] | 7900.0 |
| 최대 속도 [m/s] | 5.0 |
| 최대 가속도 [m/s²] | 40.0 |
| 최소 주위 온도 [°C] | 0.0 |
| 최대 주위 온도 [°C] | 80.0 |
| 슬라이드를 포함한 베이스의 사하중 [kg] | 9.1 |
| 스트로크 100mm당 추가 질량 [kg] | 1.45 |
| 슬라이드 중량 [kg] | 3.8 |
| 슬라이드 플레이트 길이 [mm] | 280.0 |
| 유도 시스템 | 레일 가이드 |
| 레일 수 | 1.0 |
| 레일 크기 | 20 |
| 드라이브 컨셉 | 벨트 드라이브 |
| 유휴 토크 [Nm] | 2.5 |
| 관성의 모멘트 [kgm²] | 0.0126 |
| 톱니 벨트 유형 | 40 AT 10 |
| 회전당 이송 경로 [mm] | 200.0 |
| 길이 X [mm] | 480.0 |
| 너비 Y [mm] | 100.0 |
| 높이 Z [mm] | 105.0 |
| 모멘트 Mx 최대 [Nm] | 200.0 |
| 모멘트 My 최대 [Nm] | 300.0 |
| 모멘트 Mz 최대 [Nm] | 300.0 |
| 포스 Fy 최대 [N] | 1000.0 |
| 포스 Fz 최대 [N] | 3000.0 |
| 포스 Fz 최대 [N] | 2000.0 |
소음 감소 (SAG)를 갖춘 SCHUNK 표준 스핀들 서포트는 2 SAG마다 최대 스트로크를 10 mm 줄입니다.
스핀들 축의 관성 모멘트는 1미터를 기준으로 합니다.
Dimensioni e carichi massimi
Max. Antriebskraft (Zahnriemen)*
Dimensioni e carichi massimi
Le forze e le coppie indicate si riferiscono ai valori massimi in caso di sollecitazione singola. Se si applicano più forze e/o momenti contemporaneamente, i valori individuali saranno più bassi.
Max. Antriebskraft (Zahnriemen)*
- X축:
- Velocità
- Y축:
- Forza motrice
General notes about the series
Ambient conditions
The modules are mainly designed for the use in clean ambient conditions. Please note that the life time of the modules can shorten if they are used in harsh ambient conditions, and that SCHUNK cannot assume liability in such cases. Please contact us for assistance.
Max. stroke
is the maximum permissible stroke. Acceleration and braking distances or possible overrun must be taken into consideration.
Repeat accuracy
defined as the spread of the target position after 100 consecutive positioning cycles under constant conditions.
Acceleration and speed
The values specified are the maximum values of the units without loading. The actual accelerations and speeds for your application must be designed separately and can deviate from the maximum values.
Layout or control calculation
Verifying the sizing of the selected unit is necessary, since otherwise overloading can result. Please contact us for assistance.
Operating principle
Choice of toothed belt or ball screw spindle drive
Drive
servomotors of different providers can be trouble-free adapted
Profile
Extruded aluminum profile with plastic cover strip
Slide
Aluminum slide with a brush seal
Scope of delivery
Assembly and operating manual with declaration of incorporation
Warranty
24 months